manualshive.com logo in svg

YASKAWA GPD 506/P5, Руководство по устранению неисправностей, Страница: 11 / 67

Поделиться
Скачать
YASKAWA GPD 506/P5 Скачать руководство пользователя страница 11

PP.P5G5.03.Troubleshoot

Page 11

Rev. 06/11/2003

The motor speed has exceeded the overspeed level 

when operating in the Closed Loop V/f or Closed 

Loop Flux Vector modes.

OS

Overspeed Det

N/A

Feedback pulses are not received by the PG option 

board.

PGO

PG open

N/A

Possible Cause(s): 

The load has changed considerably, the program settings may not be 

set correctly.

Corrective Action: 

Check the load on the motor, verify the program settings (F1-08 PG 

Overspeed Level, and F1-09 PG Overspeed Time).

Possible Cause(s): 

The Pulse Generator feedback wires may be broken or not properly

connected to the PG feedback option board.

Corrective Action: 

Check for a broken wire or a loose connection from the Pulse 

Generator, verify the program settings.

505

Fault Codes

Major Fault 

- Motor coasts to a stop, the fault is displayed on the digital  

operator, and the fault relay is activated. 

506 

515 

√

505

506 

515 

√

Содержание GPD 506/P5




































































Отзывы:

Нет отзывов