manualshive.com logo in svg

YASKAWA GPD 506/P5, Руководство по устранению неисправностей, Страница: 26 / 67

Поделиться
Скачать
YASKAWA GPD 506/P5 Скачать руководство пользователя страница 26

PP.P5G5.03.Troubleshoot

Page 26

Rev. 06/11/2003

Fault Codes                    

Minor Fault 

- Operation continues and the digital operator indication blink  

The fault relay does not activate.

The main circuit or control circuit voltage has fallen 
below the under voltage trip point momentarily.

A minor fault contact output can be programmed by 
using the multi-function outputs. (GPD515/G5 only)

UV

DC Bus Undervolt

U

u

The DC bus voltage has exceeded the overvoltage 
trip point while the inverter output is off.

OV

DC Bus Overvolt

ou

Possible Cause(s): 

Single phase condition on the input, low input voltage at L1, L2, and L3.

Corrective Action: 

Check the three phase input voltage, verify setting of L2-05 for GPD515/G5

Possible Cause(s): 

High input voltage at L1, L2, and L3. Power factor correction 

capacitors are being used on the input to the inverter.

Corrective Action: 

Check the input circuit, verify the program parameters, add a braking 

resistor, remove power factor correction capacitors.

505

506 

√

   

515 

√

Содержание GPD 506/P5




































































Отзывы:

Нет отзывов