background image

8

SECTION 4:  OPERATING YOUR CHIPPER SHREDDER VACUUM 

WARNING: The operation of any chipper
shredder vacuum can result in foreign
objects being thrown into the eyes, which
can damage your eyes severely. Always
wear the safety glasses provided with this
unit or eye shields before chipping or
blowing and while performing any
adjustments or repairs. 

Gas And Oil Fill-Up

Service the engine with gasoline and oil as instructed in 
the separate engine manual packed with your chipper 
shredder vacuum. Read instructions carefully.

WARNING: Never fill fuel tank indoors with
engine running or until the engine has
been allowed to cool for at least two
minutes after running.

Starting Engine

Attach spark plug wire to spark plug. Make certain 
the metal cap on the end of the spark plug is 
fastened securely over the metal tip on the spark 
plug.

Make sure safety switch wire is connected to 
engine and properly grounded.

Engines with choke lever:
Move choke lever on engine to CHOKE position. (A 
warm engine may not require choking).
Engines with primer:
Prime engine as instructed in separate engine 
manual.

The throttle control is located on the engine. Move 
engine throttle control lever to FAST or ON position.

Stand behind unit, grasp starter handle and pull 
rope out slowly until engine reaches start of 
compression cycle (rope will pull slightly harder at 
this point). 

Pull rope with a rapid, continuous, full arm stroke. 
Keep a firm grip on starter handle. Let rope rewind 
slowly.

Repeat previous steps until engine fires. When 
engine starts, move choke control (if equipped) 
gradually to RUN position.

WARNING: Never run the engine indoors
or in a poorly ventilated area. Engine
exhaust contains carbon monoxide, an
odorless and deadly gas. 

To Empty Bag

Unhook bag straps from the lower handle and 
unsnap bag clip from the top of lower handle.
See Figure 6.

Grasp bag handle with one hand and pull lock rod 
on mounting bracket with other hand toward engine 
to release.

Remove bag from rim of the discharge opening. 
Refer to Figure 3.

Twist the two buttons on the back of the bag to 
unlock and empty contents. See Figure 6.

Hold bag handle and bag clip while emptying the 
contents.

Compress bag opening and fold inner flap over 
opening.

Fold outer flap over inner flap and insert buttons on 
the bag through metal outlets.

Twist the buttons to lock bag.

Figure 6 

To Remove Blower Chute 

(If Equipped)

Grasp blower chute with one hand and pull lock rod 
on mounting bracket with other hand toward engine 
to release. Refer to Figure 4.

Remove blower chute from rim of the discharge 
opening.

Using the Chipper Shredder Vacuum

Place both hands on top of upper handle to push unit 
over yard waste. Yard waste such as leaves and pine 
needles can be vacuumed up through the nozzle for 
shredding. After material has been shredded by the flail 
blades on the impeller assembly, it will be discharged 
into catcher bag or through blower chute. Do not 
attempt to shred or chip any material other than 
vegetation found in a normal yard (i.e. branches, 
leaves, twigs, etc.) Avoid fibrous plants such as tomato 

Buttons

Inner Flap

Outer Flap

Bag Handle

Strap

Bag Clip

Содержание 24A-020D401





















Отзывы: