Yard-Man 24A-020D401 Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 20

background image

15

Model 24A-020D401

Ref.

No.

Part No.

Part Description

1.

725-1700

Switch Cover

2.

725-3166

Safety Switch

3.

710-0224

Hex Washer Screw #10-16 x.50

4.

629-0920

Wire Harness

5.

710-0604A

Hex Washer Screw 5/16-18 x.625

6.

714-0104

Cotter Pin

7.

736-0264

Flat Washer.330 ID x.630 OD

8.

732-0962

Compression Spring

9.

781-0778A

Mounting Bracket

10.

747-1153

Lock Rod

11.

710-3008

Hex Cap Screw 5/16-18 x.75

12.

681-0122

Chipper Chute Assembly

13.

726-0454

U-Clip Lock Nut 5/16-18

14.

736-0607

External Lock Washer 5/16

15.

710-0502A

Hex Washer Screw 3/8-16 x 1.25

16.

710-0969

Screw #12-16 x 1.0

17.

710-3195

Hex Cap Screw 5/16-18 x 4.5

18.

710-3025

Hex Cap Screw 5/16-18 x.625

19.

710-0604A

Hex Washer Screw 5/16-18 x.625

20.

781-1085

Upper Housing

21.

710-1054

Hex Screw 5/16-24 x 1.0

22.

781-0490

Chipper Blade

23.

736-0119

Lock Washer 5/16

24.

712-0411

Hex Lock Nut 5/16-24

25.

681-0152

Impeller Assembly

26.

719-0329

Flail Blade

27.

781-0735

Pin Clip

28.

711-1401

Clevis Pin

29.

715-0166

Spiral Pin

30.

736-0247

Flat Washer.375 ID x 1.25 OD

31.

736-0217

Lock Washer 3/8

32.

710-0818

Hex Cap Screw 3/8-24 x 2.0

33.

681-0154

Screen Assembly

34.

710-3038

Hex Cap Screw 5/16-18 x.875

35.

781-0721A

Lower Housing

36.

712-3004A

Lock Nut 5/16-18

37.

731-2265

Nozzle Cover

38.

712-0158

Lock Nut 5/16-18

39.

731-1613

Safety Switch Cover

Ref.

No.

Part No.

Part Description

NOTE: For painted parts, please refer to
the list of color codes below. Please add
the applicable color code, wherever
needed, to the part number to order a
replacement part. For instance, if a part
numbered 700-xxxx is painted Yard-Man
Green, the part number to order would be
700-xxxx-0665.

Yard-Man Green: 0665

Yard-Man Yellow: 0674

Powder Black: 0637

«
...
13
14
15
16
17
...
»

Содержание 24A-020D401





















Отзывы:

Нет отзывов

Похожие инструкции для 24A-020D401

Бренд: Timberwolf Страницы: 49

Бренд: HSM Страницы: 104

Бренд: HSM Страницы: 156

Бренд: Gartenmeister Страницы: 56

Бренд: Olympia Страницы: 70

Бренд: LawnMaster Страницы: 26

Бренд: Kellfri Страницы: 40

Powershred 1800MC

Бренд: Fellowes Страницы: 8

Бренд: Gearmore Страницы: 26

Powershred C-220

Бренд: Fellowes Страницы: 2

Бренд: Fellowes Страницы: 3

Бренд: Fellowes Страницы: 2

Бренд: Black & Decker Страницы: 1

Бренд: Texas Страницы: 14

TW 280PHB (Petrol)

Бренд: Timberwolf Страницы: 62

TW 280FTR (Petrol)

Бренд: Timberwolf Страницы: 68

Бренд: Scheppach Страницы: 36

Бренд: Snapper Страницы: 26

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды