background image

14

15

PRODUCT SAFETY WARNINGS

− Only charge the rechargeable battery indoors as the 

charger is only intended for indoor use.

− Do not place any objects on the charger and do not 

cover it as this may cause it to overheat. Do not place the 

charger near a heat source.

− Protect the charger and the battery from heat, e.g. 

in permanent sunlight or fire, and also protect it from 

water and humidity. Otherwise, there is a risk of the 

rechargeable battery exploding.

− Make sure that no moisture comes into contact with the 

charger. Otherwise there is a risk of electric shock.

− Never position the charging device in such a way that it 

could fall into a bathtub or washbasin.

− Never reach to retrieve the charger if it has fallen in 

water. In such a case, immediately disconnect the mains 

plug from the socket.

− Ensure that children do not insert objects into the 

battery or the charging device.

− Do not use the charger for purposes other than those 

intended. The charger is only intended for charging the 

same rechargeable battery also shipped with the charger.

− Do not attempt to charge the rechargeable battery 

with a charger other than the enclosed one. The charger 

shipped with this power tool and the rechargeable battery 

must be used together.

− Only replace the rechargeable battery with the same 

type or an equivalent rechargeable battery type. Refer to 

the chapter “Technical Data”.

− Do not allow battery fluid to come into contact 

with skin,eyes or mucus membranes. In the event of 

contact with battery acid, immediately flush the affected 

PRODUCT SAFETY WARNINGS

breaks or are deformed. Only replace damaged parts with 

corresponding original spare parts.

− Under no circumstances should you dismantle the 

charger. Repairs may only be performed by an authorised 

technical support team. Incorrectly performed assemblies 

could pose a risk of fire or electric shock.

− If the mains connection line of the charging device 

is damaged, it must be replaced by the manufacturer, 

its customer service department or a similarly qualified 

person in order to prevent risks.

− Only connect the charger if the mains voltage of the 

socket corresponds to the nameplate specification.

− Only connect the charger to an easily accessible 

socket, so that you can quickly disconnect it from the 

mains in case of a failure.

− Laythepowercableoutinsuchawaythatitdoesnotposeatri

ppinghazard.

− Do not kink the mains cord and do not lay it over sharp 

edges.

− Never use the mains cord as a carrying handle.

− Do not operate the charging device with an external 

timer or separate telecontrol system.

− Do not use any adapter plugs together with the 

charging device.

− Do not use any extension cords unless it is unavoidable.

Using an extension cord that is not suitable may result in 

a fire or risk of electric shock.

− Never use the charger in environments with explosive or 

flammable materials. There is a risk of fire and explosion.

− Always make sure there is adequate ventilation when 

recharging the rechargeable battery. Gases may be 

produced.

Содержание LS C08

















Отзывы: