background image

CH1900 Series Electronic Control Installation Manual 

Page  

Notice to Boat Manufacturer, Installer, and Consumer

Throughout  this  manual,  warnings  are  used  to  alert  the  installer/operator  to  special  instructions  concerning  a 
particular service or operation that may be hazardous if performed incorrectly or carelessly.  Observe these alerts 
carefully!

These “safety alerts” alone cannot eliminate the hazards that they signal.  Strict compliance to these special 
instructions when performing installation, operation, and maintenance plus “common sense” operation are the 
most effective accident prevention measures.

This device should not be used as a navigational aid to prevent collision, grounding, boat damage, or personal 
injury.  When the boat is moving, water depth may change too quickly to allow time for you to react.  Always 
operate the boat at very slow speeds if you suspect shallow water or submerged objects.

Disassembly and repair of this electronic unit should only be performed by authorized service personnel.  Any 

modification  of  the  serial  number  or  attempt  to  repair  the  original  equipment  or  accessories  by  unauthorized 

individuals will void the warranty.  Handling and/or opening this unit may result in exposure to lead, in the form 
of solder.

This product contains lead, a chemical known to the State of California to cause cancer, birth defects, and other 
reproductive harm.

This product has been designed to be compliant with the above Directive.

Maximum performance, and compliance with the EMC Directive, can only be ensured by correct installation.  It 
is strongly recommended that the installation conforms with the following standards:

APPLICABLE STANDARDS

a) ISO 8846 Small Craft-Electrical Devices

  Protection against ignition of surrounding flammable gases.

b) ISO = International Standards Organization

This device meets or exceeds the applicable ABYC, ISO, and USCG safe boating rules, regulations, standards, 
and guidelines.

 

SAFE BOATING ON THE WEB
U.S. Coast Guard 

www.uscg.mil

U.S. Power Squadron www.usps.org

NMEA 000

®

 is a registered trademark of the National Marine Electronics Association.

The information contained in this manual is believed to be accurate at the time of going to print but no responsibility, direct or consequential, can be accepted for damage 
resulting from the use of this information.  The manufacturers reserve the right to make changes, without notice, to any of its products.

RECREATIONAL CRAFT DIRECTIVE 94/25/EC

Warning

Warning

Содержание CH1900 Series













Отзывы: