Yanmar AW70V Скачать руководство пользователя страница 88

Страница: 88 / 106

Periodic Inspection

1- Loosen the fixing bolt and use the adjusting nut to

change the chain tension.

2- After checking the bending of part A, tighten the bolt

and mount the side cover.

21. Adjusting the belts

Checking the belt tensioning wheel

Spark may be generated during operation
and cause fire if the belt tensioning wheel
is in contact with other parts (except the
belt).

[Precaution]

Check whether the belt tensioning wheel is in

contact with other parts before daily operation.

Adjust immediately in case of contact, and check

the internal bearing of belt wheel.

Cooling fan belt (engine)

Press the belt center with your finger to adjust the

deflection to 12.5

2.5mm.

<Adjusting>

1- Open the engine room cover.

2- Loosen the fastening bolt of generator.

3- Draw the generator to the direction of arrow to

tension the belt.

4- Tighten the fastening bolt.

Adjusting the tension of threshing clutch

belt

Put the threshing clutch lever to “ON” and check

whether the size of tension spring falls between 190

2mm.

<Adjusting>

1- Remove the two covers of engine rear side.

2- Put the threshing clutch lever to “ON”.

3- Loosen the lock nuts (2 pieces) of threshing clutch

lever, and use the tensioning screw to adjust the

spring length to 190

2mm, as shown below.

Adjusting the tension of header clutch belt

Put the header clutch lever slightly to “ON” and check

whether the tension spring size falls in 233±2mm.

Deflection 12.5±2.5mm

Engine fixing bolt

Lock nut

190

2mm

233±2mm

https://tractormanualz.com/yanmar/

Содержание AW70V











































































































Результаты поиска

Содержание AW70V

Отзывы:

Похожие инструкции для AW70V

Бренды по названию

Популярные бренды

Yanmar AW70V, Руководство оператора

Результаты поиска

Содержание AW70V

Отзывы:

Похожие инструкции для AW70V

Бренды по названию

Популярные бренды