Yanmar AW70V Скачать руководство пользователя страница 20

Страница: 20 / 106

Safety Instructions

IMPORTANT

Load and unload the battery in the correct order.

Connect the anode firstly, and then connect the cathode when installing the battery.
Disconnect the cathode firstly, and then disconnect the anode when unloading the battery.

[If not]

Burning and fire may be caused due to short-circuit.

IMPORTANT

Use the designated battery only.
Be sure to use the battery of the capacity specified in the Operator’s Manual for
replacement when necessary.

[If not]

Burning and fire may be caused due to short-circuit.

Be sure to turn off the engine and lock the brake pedal during checking and maintenance.

Turn off the engine, lock the brake pedal, and put non-skid device under

the pulley before checking and maintaining the machine on an even ground.

[If not]

The combine may move suddenly and cause accident.

Be sure to check and maintain the brake.

It will be very dangerous if the brake does not work.

Be sure to perform inspection and maintenance of the brake on a regular basis.

[If not]

Fatal or injury accident may be caused, and the machine may be damaged.

https://tractormanualz.com/yanmar/

Содержание AW70V











































































































Результаты поиска

Содержание AW70V

Отзывы:

Похожие инструкции для AW70V

Бренды по названию

Популярные бренды

Yanmar AW70V, Руководство оператора

Результаты поиска

Содержание AW70V

Отзывы:

Похожие инструкции для AW70V

Бренды по названию

Популярные бренды