Yamato Pure Line WL320A Скачать руководство пользователя страница 13

Страница: 13 / 49

2. Before operating the unit

Installation procedures

3. Carry out connection on the main body side.

(1) Remove rubber cap from the water

inlet plug

⑧

(2) With the sleeve slid in the

direction indicated with arrow,

and insert the main body water

inlet plug

⑧

to the socket

⑨

Connection is completed when

the sleeve returns to the original

position when released. The

socket has a built-in valve. This

valve does not open and allow

water to flow unless connected

with the inlet valve

⑧

Feed water hose

Main body side

4.Be sure to connect the feed water hose to the faucet equipped with the sink.

Connection of the hose to the faucet

without sink equipment may cause

damage in the case of disconnection or

damage of the hose. Always connect to

the faucet equipped with the sink.

5. When the sink is distanced from the faucet, use an op

tional “inlet unit” (see

P.24).

The “inlet unit” is of a construction in which the connection to the faucet is harder to loosen

than the standard feed water hose set even under fluctuating water supply pressure.

When the faucet is not available, select the appropriate coupling joint from
optional “connector coupler joints” (see P.24).

Faucet

Feed water
hose

Connector
side
socket

Connector
main body

Sink

Sleeve

⑧

Inlet valve

Valve

⑨

Socket

Содержание Pure Line WL320A


















































Результаты поиска

Содержание Pure Line WL320A

Отзывы:

Бренды по названию

Популярные бренды

Yamato Pure Line WL320A, Инструкция по эксплуатации

Результаты поиска

Содержание Pure Line WL320A

Отзывы:

Бренды по названию

Популярные бренды