Yamato Pure Line WL320A Скачать руководство пользователя страница 11

Страница: 11 / 49

2. Before operating the unit

Precautions for installation

9. Installation

●

The model WL320A is a desktop type with rubber feet.

●

The model WL320B is a floor type with caster wheels.

。

10 Be sure to keep the raw water pressure from water supply within the specified

range.

●

Use the supply water pressure within a range of 0.5

～

100kPa

（

0.5

～

5kgf/cm

）

hours a day.

Note that the water sampling range becomes 1.0 L/min or less at the raw water pressure

of 1.0

100kPa

（

1kgf/cm

）

or less.

●

The raw water pressure range is the same even when the optional water inlet unit(see

Page 24) is used.

11.About raw water

●

Check if raw water is not contaminated with red rust or other dirt. If raw water is

contaminated, the specified water quality will not be assured and a malfunction may result.

●

Use tap water for raw water.

The model WL320A

is a desktop type

The model WL320B is a floor type

Содержание Pure Line WL320A


















































Результаты поиска

Содержание Pure Line WL320A

Отзывы:

Бренды по названию

Популярные бренды

Yamato Pure Line WL320A, Инструкция по эксплуатации

Результаты поиска

Содержание Pure Line WL320A

Отзывы:

Бренды по названию

Популярные бренды