Yamaha YZF-R6T Скачать руководство пользователя страница 78

Страница: 78 / 111

PERIODIC MAINTENANCE AND MINOR REPAIR

6-32

EAU23200

Checking and lubricating the
sidestand

The operation of the sidestand should
be checked before each ride, and the
sidestand pivot and metal-to-metal
contact surfaces should be lubricated if
necessary.

WARNING

EWA10730

If the sidestand does not move up
and down smoothly, have a Yamaha
dealer check or repair it.

EAUM1650

Lubricating the swingarm
pivots

The swingarm pivots must be lubricat-
ed at the intervals specified in the peri-
odic maintenance and lubrication chart.

Recommended lubricant:

Lithium-soap-based grease (all-pur-
pose grease)

Recommended lubricant:

Lithium-soap-based grease (all-pur-
pose grease)

Recommended lubricant:

Lithium-soap-based grease

U5SL12E0.book Page 32 Monday, August 9, 2004 10:51 AM

Содержание YZF-R6T
















































































































Результаты поиска

Содержание YZF-R6T

Отзывы:

Похожие инструкции для YZF-R6T

Бренды по названию

Популярные бренды

Yamaha YZF-R6T, Руководство пользователя

Результаты поиска

Содержание YZF-R6T

Отзывы:

Похожие инструкции для YZF-R6T

Бренды по названию

Популярные бренды