Yamaha YZF-R6T Скачать руководство пользователя страница 65 | Manualshive

Страница: 65 / 111

background image

PERIODIC MAINTENANCE AND MINOR REPAIR

6-19

6

WARNING

EWA10410

●

Make sure that the fuel tank is
well supported.

●

Do not tilt or pull the fuel tank
too much, otherwise the fuel
hoses may come loose, which
could cause fuel leakage.

4. Remove the air filter case cover by

removing the screws.

5. Pull the air filter element out.

6. Check the condition of the air filter

element and replace it if it is dam-
aged or excessively dusty.

7. Insert the element into the air filter

case.

CAUTION:

ECA10480

●

Make sure that the air filter ele-
ment is properly seated in the
air filter case.

●

The engine should never be op-
erated without the air filter ele-
ment installed, otherwise the
piston(s) and/or cylinder(s) may
become excessively worn.

8. Install the air filter case cover by in-

stalling the screws.

9. Place the fuel tank in the original

position, and then install the bolts.

WARNING

EWA11360

●

Before placing the fuel tank in
the original position, make sure
that the fuel hoses are not dam-
aged. If any fuel hose is dam-
aged, do not start the engine but
have a Yamaha dealer replace
the hose, otherwise fuel may
leak.

●

Make sure that the fuel hoses
are properly connected and
routed, and not pinched.

1. Screw
2. Air filter case cover

1. Air filter element

U5SL12E0.book Page 19 Monday, August 9, 2004 10:51 AM

«
...
63
64
65
66
67
...
»

Содержание YZF-R6T
















































































































Отзывы:

Нет отзывов

Похожие инструкции для YZF-R6T

Бренд: Xenith Страницы: 17

Бренд: R&G Страницы: 14

Бренд: Suzuki Страницы: 447

Бренд: Clas Ohlson Страницы: 5

690 Enduro AUS 2010

Бренд: KTM Страницы: 265

RMAX WOLVERINE 2021

Бренд: Yamaha Страницы: 192

Бренд: Yamaha Страницы: 396

Бренд: Yamaha Страницы: 192

Бренд: Baja motorsports Страницы: 20

Бренд: BUMOT Страницы: 3

Gold Wing GL1100

Бренд: Honda Страницы: 356

Бренд: HYOSUNG Страницы: 175

Бренд: Yamaha Страницы: 84

Бренд: Yamaha Страницы: 96

Бренд: Yamaha Страницы: 98

Бренд: Yamaha Страницы: 124

Бренд: Yamaha Страницы: 356

Бренд: Yamaha Страницы: 418

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды