Yamaha YZF-R1 2004 Скачать руководство пользователя

Страница: 48 / 51

3-2

NOTE:

PERIODIC MAINTENANCE AND

LUBRICATION INTERVALS

CHK

ADJ

NO.

ITEM

CHECK OR MAINTENANCE JOB

ODOMETER READING

(

1,000 km)

ANNUAL

CHECK

Sidestand
(See page 3-61)

Check operation.

Lubricate.

Sidestand switch
(See page 3-61, 8-4)

Check operation.

Front fork
(See page 3-53)

Check operation and for oil leakage.

Shock absorber
assembly
(See page 3-56, 4-68)

Check operation and shock absorber for oil leakage.

Rear suspension relay
arm and connecting arm
pivoting points
(See page 4-72)

Check operation.

Electronic fuel injection
(See page 3-17, 21)

Adjust engine idling speed and synchronization.

Engine oil
(See page 3-26, 28)

Change.

Check oil level and vehicle for oil leakage.

Engine oil filter
cartridge
(See page 3-28)

Replace.

Cooling system

Check coolant level and vehicle for coolant leakage.

g y

(See page 3-37, 38, 39)

Change.

Every 3 years

Front and rear brake
switches
(See page 3-45)
(See page 8-4)

Check operation.

Moving parts and cables
(See page 3-61)

Lubricate.

Throttle grip housing
and cable
(See page 3-22)

Check operation and free play.

Adjust the throttle cable free play if necessary.

Lubricate the throttle grip housing and cable.

Air induction system
(See page 7-46)

Check the air cut-off valve, reed valve, and hose for dam-
age

Replace any damaged parts if necessary.

Muffler and exhaust
pipe
(See page 3-35)

Check the screw clamp for looseness.

EXUP system
(See page 3–36)

Check operation, cable free play and pulley position.

Lights, signals and
switches
(See page 3-70)

Check operation.

Adjust headlight beam.

EAU03884

Air filter

This model’s air filter is equipped with a disposable oil-coated paper element, which must not be
cleaned with compressed air to avoid damaging it.

The air filter element needs to be replaced more frequently when riding in unusually wet dusty
areas.

Hydraulic brake service

Regularly check and, if necessary, correct the brake fluid level.

Every two years replace the internal components of the brake master cylinders and calipers, and
change the brake fluid.

Replace the brake hoses every four years and if cracked or damaged.

Содержание YZF-R1 2004




















































Результаты поиска

Содержание YZF-R1 2004

Отзывы:

Похожие инструкции для YZF-R1 2004

Бренды по названию

Популярные бренды

Yamaha YZF-R1 2004, Информация о сервисе

Результаты поиска

Содержание YZF-R1 2004

Отзывы:

Похожие инструкции для YZF-R1 2004

Бренды по названию

Популярные бренды