Yamaha YZF-R1 2004 Скачать руководство пользователя

Страница: 44 / 51

2-46

DD Fasten the wire harness,

A.C.magneto lead, and
throttle body lead with a
clamp. Point the tip of the
clamp (cut the tip of the clamp
leaving 2 to 4 mm (0.08 to 0.16
in).) to the inside of the ve-
hicle.

EE To the air filter

FF To the throttle body

GG To install the cover 7, install so

as to set each coupler in the
cover. Make sure that each
lead is not caught by the cover
7.

Z Point the tip of the clamp (exces-

sive part) to the down side of the
vehicle. Fasten the wire har-
ness, battery negative lead, A.C.
magneto lead and starter motor
lead with a clamp.

AA To the speed sensor
BB Insert the wire harness wrap-

ping clamp to the hole of the
frame.

CC After passing the lead be-

tween the wire harness and
starter motor leads, fastening
by the clamp should be can-
celled and route the lead un-
der the idle remote controller.

CABLE ROUTING

SPEC

HH Insert the wire harness wrap-

ping clamp to the hole of the
frame.

Make sure that the lead is fas-
tened with the guide of the ra-
diator stay.

JJ To the right handlebar switch

KK Do not place it beyond pipe 3

in the direction to the external
part of the vehicle.

LL Battery negative lead should

not run on the swingarm
bracket.

Содержание YZF-R1 2004




















































Результаты поиска

Содержание YZF-R1 2004

Отзывы:

Похожие инструкции для YZF-R1 2004

Бренды по названию

Популярные бренды

Yamaha YZF-R1 2004, Информация о сервисе

Результаты поиска

Содержание YZF-R1 2004

Отзывы:

Похожие инструкции для YZF-R1 2004

Бренды по названию

Популярные бренды