background image

PERIODIC MAINTENANCE AND ADJUSTMENT

7-17

1

2

3

4

5

6

7

8

9

10

11

12

weight of rider, passenger, car-
go, and accessories approved
for this model.

WARNING

EWA10512

Never overload your vehicle. Opera-
tion of an overloaded vehicle could
cause an accident.

Tire inspection

The tires must be checked before each
ride. If the center tread depth reaches
the specified limit, if the tire has a nail or
glass fragments in it, or if the sidewall is
cracked, have a Yamaha dealer re-
place the tire immediately.

TIP

The tire tread depth limit may differ
from country to country. Always comply
with the local regulations.

WARNING

EWA17960

It is dangerous to ride with a
worn-out tire. When a tire tread
depth reaches the specified lim-
it, have a Yamaha dealer replace
the tire immediately.

The replacement of all wheel
and brake-related parts, includ-
ing the tires, should be left to a
Yamaha dealer, who has the
necessary professional knowl-
edge and experience.

It is not recommended to patch
a punctured tube. If unavoid-
able, however, patch the tube
very carefully and replace it as
soon as possible with a
high-quality product.

Ride at moderate speeds after
changing a tire since the tire
surface must first be “broken
in” for it to develop its optimal
characteristics.

Tire information

This model is equipped with tube tires.
Tires age, even if they have not been

Tire air pressure (measured on cold 
tires):

Up to 90 kg (198 lb) load:

Front:

125 kPa (1.25 kgf/cm

2

, 18 psi)

Rear:

150 kPa (1.50 kgf/cm

2

, 22 psi)

90 kg (198 lb) to maximum load:

Front:

150 kPa (1.50 kgf/cm

2

, 22 psi)

Rear:

175 kPa (1.75 kgf/cm

2

, 25 psi)

Maximum load*:

150 kg (331 lb)

* Total weight of rider, passenger, car-

go and accessories

1. Tire tread depth

2. Tire sidewall

Minimum tire tread depth (front and 
rear):

1.5 mm (0.06 in)

2

1

1YB-9-22.book  17 ページ  2014年2月28日 金曜日 午前10時21分

Содержание XT250L 2014



























































































Отзывы: