Yamaha XL700 WaveRunner 2004 Скачать руководство пользователя страница 99 | Manualshive

Страница: 99 / 120

Yamaha XL700 WaveRunner 2004 Скачать руководство пользователя страница 99

4-18

E

EJU01971

Inspecting the battery

Check the level of the battery electrolyte

and make sure that the negative and posi-
tive leads are securely tightened.

WARNING

@

●

Battery electrolyte is poisonous and
dangerous, causing severe burns, etc.
Electrolyte contains sulfuric acid.
Avoid contact with skin, eyes, or cloth-
ing.
Antidotes
External: Flush with water.
Internal: Drink large quantities of water
or milk. Follow with milk of magnesia,
beaten egg, or vegetable oil. Call phy-
sician immediately.
Eyes: Flush with water for 15 minutes
and get prompt medical attention.
Batteries produce explosive gases.
Keep sparks, flame, cigarettes, etc.,
well away. If using or charging the bat-
tery in an enclosed space, make sure
that it is well ventilated. Always shield
your eyes when working near batter-
ies.
KEEP OUT OF THE REACH OF CHIL-
DREN.

●

Be sure to connect the breather hose
to the battery. Fire or explosion could
result if the breather hose is damaged,
obstructed, or not connected properly.

@

CAUTION:

@

●

Be careful not to place the battery on
its side.

●

Be sure to remove the battery from the
battery compartment when adding
electrolyte or charging the battery.

@

UF0M15.book Page 18 Tuesday, June 3, 2003 3:36 PM

«
...
97
98
99
100
101
...
»

Содержание XL700 WaveRunner 2004

























































































































Отзывы:

Нет отзывов