Yamaha XL700 WaveRunner 2004 Скачать руководство пользователя страница 48

Страница: 48 / 120

3-3

EJU01135

Filling the fuel tank

CAUTION:

Be careful when refueling. Avoid getting
water or other contaminants in the fuel
tank. Contaminated fuel can cause poor
running or engine damage.

1. Open the hood and remove the front

storage compartment. Also, remove all
seats, so you can watch the fuel level.
(See page 2-6 for hood, and pages 2-4
and 2-5 for seats.)

2. Open the fuel tank filler cap, and slowly

add fuel to the fuel tank.

3. Stop filling when the fuel just reaches the

bottom of the filler tube on the fuel tank.
Do not fill into the filler tube, because
fuel could spill out.

Fuel tank capacity:

Total: 50 L (13.2 US gal, 11 Imp gal)
Reserve: 12 L (3.2 US gal, 2.6 Imp gal)

UF0M15.book Page 3 Tuesday, June 3, 2003 3:36 PM

Содержание XL700 WaveRunner 2004

























































































































Результаты поиска

Содержание XL700 WaveRunner 2004

Отзывы:

Yamaha XL700 WaveRunner 2004, Руководство владельца/оператора, Страница: 48 / 120

Результаты поиска

Содержание XL700 WaveRunner 2004

Отзывы: