Yamaha XL700 WaveRunner 2004 Скачать руководство пользователя страница 47

Страница: 47 / 120

3-2

●

If any gasoline spills onto your skin,
immediately wash with soap and
water. Change clothing if gasoline
spills on it.

CAUTION:

Use only fresh gasoline that has been
stored in clean containers.

EJU01832

Gasohol

There are two types of gasohol: gasohol

containing ethanol and that containing meth-
anol.

Gasohol containing ethanol can be used

if ethanol content does not exceed 10% and
the fuel meets minimum octane ratings.

Gasohol containing methanol is not rec-

ommended by Yamaha because it can
cause fuel system damage or engine perfor-
mance problems.

EJU10441

2-stroke engine oil

If YAMALUBE 2-W oil is not available,

another 2-stroke engine oil with an NMMA-
certified TC-W3 rating may be used.

Recommended gasoline:

Regular unleaded gasoline with a mini-
mum octane rating of
86 (Pump octane number) = (R+M)/2
90 (Research octane number)

Recommended engine oil:

YAMALUBE 2-W oil

UF0M15.book Page 2 Tuesday, June 3, 2003 3:36 PM

Содержание XL700 WaveRunner 2004

























































































































Результаты поиска

Содержание XL700 WaveRunner 2004

Отзывы:

Yamaha XL700 WaveRunner 2004, Руководство владельца/оператора, Страница: 47 / 120

Результаты поиска

Содержание XL700 WaveRunner 2004

Отзывы: