Yamaha XL700 WaveRunner 2004 Скачать руководство пользователя страница 86 | Manualshive

Страница: 86 / 120

Yamaha XL700 WaveRunner 2004 Скачать руководство пользователя страница 86

4-5

E

Top off the fuel tank with fresh gasoline

and add one ounce of Yamaha Fuel Stabi-
lizer and Conditioner to each gallon of fuel.

NOTE:

@

Use of Yamaha Fuel Stabilizer and Condi-
tioner eliminates the need to drain the fuel
system. If the fuel system is to be drained
instead, consult a Yamaha dealer.

@

EJU01970

Battery

If the watercraft will not be used for more

than a month, disconnect the negative (–)
lead first, then the positive (+) lead and
breather hose, and then remove the battery
from the watercraft.

Clean the battery casing using fresh

water.

If the battery terminals are dirty or cor-

roded, clean them with a wire brush.

Fully charge the battery, and then store it

in a cool, dark place.

Apply Yamaha marine grease or Yamaha

grease A to the battery terminals.

Check the battery at least every 2 months

and fully charge it if necessary.

WARNING

@

Be sure to connect the breather hose to
the battery. Fire or explosion could result
if the breather hose is damaged,
obstructed, or not connected properly.

@

CAUTION:

@

The battery may not be usable again if
you store it for a long period without
charging it. Charge the battery periodi-
cally.

@

UF0M15.book Page 5 Tuesday, June 3, 2003 3:36 PM

«
...
84
85
86
87
88
...
»

Содержание XL700 WaveRunner 2004

























































































































Отзывы:

Нет отзывов