Yamaha WOLVERINE X2 2021 Скачать руководство пользователя страница 157

Страница: 157 / 186

9-46

place the tires in pairs (front or rear) with tires
of the same size and type as the originals.
Never replace just one tire.

WARNING

EWB03390

Installing improper tires on your Yamaha
WolverineX2 can affect handling and sta-
bility. This can cause a loss of control.

The tires listed below have been approved by
Yamaha Motor Manufacturing Corporation of
America for this model.

EBU33090

Wheel installation

1. Install the wheel and the nuts.
2. Lower the vehicle so that the wheel is on

the ground.

3. Tighten the wheel nuts in a crisscross

pattern to the specified torque.

WARNING

EWB03400

Do not reverse the rims on your Yamaha
WolverineX2 to widen the track width. In-
stalling wheels improperly increases the
risk of wheel failure and accidents.

Front tire:

Size:

27x9R12 NHS

Manufacturer/model:

GBC/DIRT COMMANDER

Rear tire:

Size:

27x11R12 NHS

Manufacturer/model:

GBC/DIRT COMMANDER

Tightening torques:

Front wheel nut:

75 N·m (7.5 kgf·m, 55 lb·ft)

Rear wheel nut:

75 N·m (7.5 kgf·m, 55 lb·ft)

UBAN12E0.book Page 46 Wednesday, June 30, 2021 2:17 PM

Содержание WOLVERINE X2 2021



























































































































































































Результаты поиска

Содержание WOLVERINE X2 2021

Отзывы:

Похожие инструкции для WOLVERINE X2 2021

Бренды по названию

Популярные бренды

Yamaha WOLVERINE X2 2021, Руководство пользователя

Результаты поиска

Содержание WOLVERINE X2 2021

Отзывы:

Похожие инструкции для WOLVERINE X2 2021

Бренды по названию

Популярные бренды