manualshive.com logo in svg

Yamaha WaveRunner VX Sport 2014, Руководство владельца/оператора, Страница: 8 / 98

Поделиться
Скачать
Yamaha WaveRunner VX Sport 2014 Скачать руководство пользователя страница 8

General and important labels

2

EJU42051

Manufactured date label

This label is attached to the top of the cylin-
der head. (See page 38 for seat removal and
installation procedures.)

EJU30321

Model information

EJU30332

Builder’s plate

Watercraft with this label conform to certain
portions of the European Parliament directive
relating to machinery.
Part of the information is given on the build-
er’s plate affixed on the craft. A full explana-
tion of this information is given in the relevant
sections of this manual.

Design category of this personal water-
craft: C
Category C:

This watercraft is designed to operate in
winds up to Beaufort force 6 and the associ-
ated wave heights (significant wave heights
up to 2 m (6.56 ft); see the following TIP).
Such conditions may be encountered in ex-
posed inland waters, in estuaries, and in
coastal waters in moderate weather condi-
tions.

1

Manufactured date label location

1

1

Builder’s plate location

1

UF2P71E0.book  Page 2  Wednesday, July 10, 2013  5:37 PM

Содержание WaveRunner VX Sport 2014



































































































Отзывы:

Нет отзывов