manualshive.com logo in svg

Yamaha WaveRunner VX Sport 2014, Руководство владельца/оператора, Страница: 40 / 98

Поделиться
Скачать
Yamaha WaveRunner VX Sport 2014 Скачать руководство пользователя страница 40

Instrument operation

34

TIP:

“mph” is selected as the display unit at the
Yamaha factory.

To switch the speedometer display units:
Push the select button for at least 1 second,
within 10 seconds after the multifunction in-
formation center is activated. The speedom-
eter display changes.

EJU31464

Tachometer

The tachometer shows the engine speed.

The outer numbers 

×

 1000 r/min and display

segments on the meter show the engine
speed.

EJU31556

Hour meter/voltmeter

The hour meter/voltmeter has both an hour
meter function and a voltmeter function. By
switching the meter, it can be used as either
an hour meter or a voltmeter.

TIP:

The hour meter is selected at the Yamaha
factory.

Hour meter

The hour meter shows the total number of
hours that the engine has been running since
the watercraft was new.

TIP:

The elapsed time will be kept even if the bat-
tery terminals have been disconnected.

1

Speedometer

1

Speedometer

2

Select button

1

1

2

1

Tachometer

1

Hour meter/voltmeter

1

1

UF2P71E0.book  Page 34  Wednesday, July 10, 2013  5:37 PM

Содержание WaveRunner VX Sport 2014



































































































Отзывы:

Нет отзывов