Yamaha WaveRunner VX Sport 2014 Скачать руководство пользователя страница 45 | Manualshive

Страница: 45 / 98

Yamaha WaveRunner VX Sport 2014 Скачать руководство пользователя страница 45

Equipment operation

39

(2) Push the rear of the seat down to secure-

ly lock it in place.

EJU31364

Handgrip

The handgrip is used when boarding the wa-
tercraft from the water and when the spotter
is facing rearward.

WARNING! Do not use

the handgrip to lift the watercraft. The
handgrip is not designed to support the
watercraft’s weight. If the handgrip
breaks, the watercraft could fall, which
could result in severe injury.

[EWJ00022]

EJU34865

Reboarding step (VX Deluxe /
VX Cruiser)

The reboarding step is used to assist in re-
boarding the watercraft from the water.
When boarding the watercraft, push the re-
boarding step down until it stops. The step
returns automatically to its original position
when released.

WARNING! Do not use the

reboarding step to lift the watercraft. The
reboarding step is not designed to support
the watercraft’s weight. If the reboarding
step breaks, the watercraft could fall,
which could result in severe injury.

[EWJ01212]

NOTICE

ECJ00743

Use the reboarding step only to board the
watercraft in the water. Do not use the re-
boarding step for any other purpose. The
watercraft can be damaged.

1

Handgrip

1

1

Reboarding step

1

UF2P71E0.book Page 39 Wednesday, July 10, 2013 5:37 PM

«
...
43
44
45
46
47
...
»

Содержание WaveRunner VX Sport 2014



































































































Отзывы:

Нет отзывов