Yamaha WaveRunner VX Sport 2014 Скачать руководство пользователя страница 67 | Manualshive

Страница: 67 / 98

Yamaha WaveRunner VX Sport 2014 Скачать руководство пользователя страница 67

Operation

61

is attached correctly. If the engine
shut-off cord (lanyard) is not attached
correctly, it may not pull free when the
operator falls off, allowing the water-
craft to continue to run and cause an
accident.

[EWJ00582]

(4) With the throttle lever released, push the

start switch (green button) to start the
engine. (See page 27 for information on
operating the start switch.)

EJU32863

Stopping the engine

Release the throttle lever, and then push the
engine stop switch (red button) to stop the
engine.

WARNING! You need throttle to

steer. Shutting the engine off can cause
you to hit an obstacle you are attempting

to avoid. A collision could result in severe
injury or death.

[EWJ00602]

EJU32873

Leaving the watercraft

If leaving the watercraft, remove the clip from
the engine shut-off switch to prevent acci-
dental starting or unauthorized operation by
children or others.

EJU41573

Operating the watercraft

VX Sport:

When the engine is running, the watercraft
will move forward at trolling speed even if the

1

Clip

2

Engine shut-off switch

3

Engine shut-off cord (lanyard)

1

2

3

STAR

T

ST

OP

UF2P71E0.book Page 61 Wednesday, July 10, 2013 5:37 PM

«
...
65
66
67
68
69
...
»

Содержание WaveRunner VX Sport 2014



































































































Отзывы:

Нет отзывов