Yamaha VZ150D Скачать руководство пользователя страница 44 | Manualshive

Страница: 44 / 81

background image

Operation

39

to allow operation in shallow water.

WARNING

EWM00660

●

Place the gear shift in neutral before
setting up for shallow water cruising.

●

Return the outboard motor to its normal
position as soon as the boat is back in

deeper water.

CAUTION:

ECM00260

Do not tilt the outboard motor up so that
the cooling water inlet on the lower unit is
above the surface of the water when set-
ting up for and cruising in shallow water.
Otherwise severe damage from overheat-

ing can result.

EMU28184

Procedure for power trim and tilt / power
tilt models

1.

Place the gear shift lever in neutral.

2.

Slightly tilt the outboard motor up to the
desired position using the power trim / tilt
switch.

3.

To return the outboard motor to the nor-
mal running position, press the power
trim / tilt switch and slowly tilt the out-
board motor down.

EMU28190

Cruising in other conditions

Cruising in salt water

After operating in salt water, wash out the
cooling water passages with fresh water to
prevent them from becoming clogged with
salt deposits.

NOTE:

For cooling system flushing instructions, see

page 41.

Cruising in turbid water

Yamaha strongly recommends that you use
the optional chromium-plated water pump kit
if you use the outboard motor in turbid (mud-
dy) water conditions.

UP

ZMU01935

UP

DN

UP

ZMU04000

«
...
42
43
44
45
46
...
»

Содержание VZ150D


















































































Отзывы:

Нет отзывов

Похожие инструкции для VZ150D

Бренд: Abit Страницы: 120

Бренд: Intel Страницы: 78

Бренд: Giada Страницы: 2

Бренд: Rosch Computer Страницы: 87

Бренд: Microsemi Страницы: 15

Бренд: Tews Technologies Страницы: 26

Бренд: Biostar Страницы: 166

Бренд: Mini-Itx Страницы: 174

Бренд: Variscite Страницы: 2

Бренд: Fujitsu Siemens Computers Страницы: 20

Бренд: PRIZM Страницы: 9

STEVAL-PLC001V1

Бренд: ST Страницы: 42

Бренд: Gigabyte Страницы: 96

Бренд: Supermicro Страницы: 95

Бренд: Zamel Страницы: 3

Spacewalker AV40

Бренд: Shuttle Страницы: 81

Бренд: Advantech Страницы: 98

Бренд: JETWAY Страницы: 48

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды