Yamaha VZ150D Скачать руководство пользователя страница 38 | Manualshive

Страница: 38 / 81

background image

Operation

33

hole at all times while the engine is run-
ning, overheating and serious damage
could occur. Stop the engine and check
whether the cooling water inlet on the
lower case or the cooling water pilot hole
is blocked. Consult your Yamaha dealer if
the problem cannot be located and cor-

rected.

EMU27740

Shifting

WARNING

EWM00180

Before shifting, make sure there are no
swimmers or obstacles in the water near

you.

CAUTION:

ECM00220

To change the boat direction or shifting
position from forward to reverse or vice-
versa, first close the throttle so that the

engine idles (or runs at low speeds).

EMU27763

Forward (tiller handle and remote
control models)

Tiller control models
1.

Place the throttle grip in the fully closed
position.

2.

Move the gear shift lever quickly and
firmly from neutral to forward.

Remote control models

1.

Pull up the neutral interlock trigger (if
equipped) and move the remote control
lever quickly and firmly from neutral to
forward.

EMU27784

Reverse (automatic reverse lock and
power trim and tilt models)

WARNING

EWM00190

When operating in reverse, go slowly. Do
not open the throttle more than half. Oth-
erwise the boat could become unstable,
which could result in loss of control and

an accident.

Tiller control models
1.

Place the throttle grip in the fully closed
position.

2.

Move the gear shift lever quickly and
firmly from neutral to reverse.

Remote control models
1.

Pull up the neutral interlock trigger (if
equipped) and move the remote control
lever quickly and firmly from neutral to
reverse.

ZMU01882

«
...
36
37
38
39
40
...
»

Содержание VZ150D


















































































Отзывы:

Нет отзывов

Похожие инструкции для VZ150D

Бренд: Qorvo Страницы: 8

TLV320AIC3111 EVM

Бренд: Texas Instruments Страницы: 39

Бренд: JETWAY Страницы: 47

Бренд: Abit Страницы: 48

Бренд: Sure Electronics Страницы: 32

Бренд: DTK Страницы: 50

Бренд: Renesas Страницы: 20

VAR-SOM-MX8M-NANO

Бренд: Variscite Страницы: 2

Бренд: IBASE Technology Страницы: 76

Бренд: AOpen Страницы: 8

Бренд: OLIMEX Страницы: 13

Бренд: Gigabyte Страницы: 76

4CORE1600-GLAN/M

Бренд: ASROCK Страницы: 102

Бренд: Gigabyte Страницы: 98

ISOFACE ISO2H823V2

Бренд: Infineon Страницы: 28

Бренд: ON Semiconductor Страницы: 7

Бренд: Intel Страницы: 29

Бренд: Supermicro Страницы: 126

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды