Yamaha VZ150D Скачать руководство пользователя страница 40 | Manualshive

Страница: 40 / 81

background image

Operation

35

EMU27881

Adjusting trim angle

Power trim and tilt models

WARNING

EWM00750

●

Be sure all people are clear of the out-
board motor when adjusting the tilt an-
gle, also be careful not to pinch any
body parts between the drive unit and
clamp bracket.

●

Use caution when trying a trim position
for the first time. Increase speed gradu-
ally and watch for any signs of instabil-
ity or control problems. Improper trim
angle can cause loss of control.

●

Use the power tilt switch located on the
bottom engine cowling (if equipped)
only when the boat is at a complete

stop with the engine off.

Adjust the outboard motor trim angle using
the power trim and tilt switch.

To raise the bow (trim-out), press the switch
“

” (up).

To lower the bow (trim-in), press the switch
“

” (down).

Make test runs with the trim set to different
angles to find the position that works best for
your boat and operating conditions.

NOTE:

To adjust the trim angle while the boat is
moving, use the power trim and tilt switch lo-
cated on the remote control device or tiller

handle, if equipped.

EMU27911

Adjusting boat trim

When the boat is on plane, a bow-up attitude

1. Trim operating angle

1

ZMU03994

1. Power trim and tilt switch

1. Power trim and tilt switch

UP

DN

ZMU04012

1

«
...
38
39
40
41
42
...
»

Содержание VZ150D


















































































Отзывы:

Нет отзывов

Похожие инструкции для VZ150D

Бренд: Aaeon Страницы: 97

Бренд: MSI Страницы: 92

Бренд: Supero Страницы: 101

Бренд: IBASE Technology Страницы: 81

Бренд: ECS Страницы: 66

Бренд: Digilent Страницы: 23

Бренд: Gigabyte Страницы: 36

z170a GAMING M9 ACK

Бренд: MSI Страницы: 109

Бренд: Texas Instruments Страницы: 26

Бренд: ALi Confidential Страницы: 24

Бренд: Advantech Страницы: 5

Бренд: MSI Страницы: 92

Бренд: Evalue Technology Страницы: 91

Бренд: Parsun Страницы: 93

Бренд: Aaeon Страницы: 53

Бренд: Aaeon Страницы: 46

Бренд: EVGA Страницы: 35

Бренд: Intel Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды