Yamaha VX WaveRunner 2007 Скачать руководство пользователя страница 61

Страница: 61 / 108

Operation

Also, make sure that the reverse gate goes up
completely when the shift lever is pushed
down.

WARNING

EWJ00480

●

Make sure that the throttle lever is com-
pletely released and that the engine is at
idle before shifting into reverse.

●

Do not use the reverse function to slow
down or stop the watercraft as it could
cause you to lose control, be ejected, or
impact the handlebars.

●

Use reverse for slow-speed maneuver-
ing only.

●

Make sure that there are no obstacles or
people behind you before shifting into
reverse.

●

Do not touch the reverse gate while the
shift lever is being operated, otherwise
you could be pinched.

EJU32641

Quick Shift Trim System (QSTS)

Operate the QSTS selector lock lever and the
QSTS selector several times to check that
they operate properly.
(1) Squeeze the QSTS selector lock lever

and check that it returns smoothly to its
original position when released.

(2) Check that the QSTS selector turns

smoothly when the lever is squeezed and
check that the selector locks in place at
each position when the lever is released.

(3) Check that the angle of the jet thrust noz-

zle changes when the QSTS selector is

UF1Y11E0.book Page 56 Wednesday, August 23, 2006 11:43 AM

Содержание VX WaveRunner 2007













































































































Результаты поиска

Содержание VX WaveRunner 2007

Отзывы:

Yamaha VX WaveRunner 2007, Руководство владельца/оператора, Страница: 61 / 108

Результаты поиска

Содержание VX WaveRunner 2007

Отзывы: