Yamaha VX WaveRunner 2007 Скачать руководство пользователя страница 45

Страница: 45 / 108

Features and functions

The following operation buttons are on the left
side of the multifunction meter.

EJU35041

Digital speedometer

The digital speedometer shows the watercraft
speed against water.

NOTE:

●

To switch the speedometer display be-
tween kilometers and miles, push the
“Volt/Hour” button for at least 1 second,
within 10 seconds after the multifunction
meter starts operating.

●

The “SPEED” indicator light blinks three
times if miles are selected as the display
units when the multifunction meter starts

operating, or if the display units of the meter
are switched to miles.

EJU31511

Fuel level meter

The fuel level meter is provided for convenient
fuel level checking while riding.

“Speed/RPM” button

“Volt/Hour” button

Digital speedometer

“Volt/Hour” button

“SPEED” indicator light

UF1Y11E0.book Page 40 Wednesday, August 23, 2006 11:43 AM

Содержание VX WaveRunner 2007













































































































Результаты поиска

Содержание VX WaveRunner 2007

Отзывы:

Yamaha VX WaveRunner 2007, Руководство владельца/оператора, Страница: 45 / 108

Результаты поиска

Содержание VX WaveRunner 2007

Отзывы: