13
6
8
7
EFFECT BAND
Selecting an Effect Band
Let’s first select a delay circuit and set its param-
eters.
The [EFFECT BAND 1-8] buttons are used to switch
the eight effect circuits ON/OFF.
1.
Press the [EFFECT BAND 1] button to select
Effect Band 1 (the selected button’s lamp will
flash rapidly).
* When an EFFECT BAND button’s lamp is flashing rap-
idly, it indicates that that Effect Band is currently being
edited.
Using the UD-Stomp
Setting the Delay Time
Next, let’s set the Delay Time.
Use the TIME COARSE (rough setting) and TIME
FINE (precise setting) knobs to set the Delay Time.
2.
In this step, we will set a delay time of 250msec.
Rotate the TIME COARSE knob until “
200.
”
appears in the display.
* The value for time used in the delay is msec (millisec-
onds). The dot indicates the position of the decimal point.
Example)
200.
= 200 msec
When the value is over 1000msec (no dot in the display),
the value in the display should be multiplied by 10.
Example)
123
= 1230 msec
If “
0.02
” is flashing in the display and the
[DOWN] lamp flashes when you rotate the knob,
it indicates that the knob’s position is not aligned
with the value set for the parameter. First ro-
tate the knob all the way to the left, then rotate
to the right to set the value.
Using the Knobs
Since the position of each knob on the panel
is not always aligned with the value set in
the parameter of the current patch, please
follow the rules described below to align the
knob with the parameter value.
• If the [UP] lamp flashes when the knob is rotated,
rotate the knob to the right (toward 10), and if the
[DOWN] lamp flashes, rotate the knob to the left
(toward 0).
At this time, the knob’s parameter value set in
the current patch is flashing in the display.
* As long as the lamp is flashing, neither the value in the
display nor the sound will change even though the knob
is being rotated.
• Continue rotating the knob in the direction de-
scribed above. Once the knob has reached the
position that corresponds to the parameter value,
the value in the display and the [UP]/[DOWN]
lamp will stop flashing and the value will now
change according to the position of the knob.
* After you stop moving the knob, the value will continue
to be displayed for about 2 seconds, after which it will
return to the normal display.
• Once the knob is aligned with the value and can
be used to edit the value, rotating the knob will
result in the value shown in the display changing
in regards to the knob’s position and a relative
change in the effect’s sound.
These rules apply to all knobs with the ex-
ception of the OUTPUT knob.
3.
Next, rotate the TIME FINE knob so that “
250.
”
is shown in the display. If “
200.
” is flashing in
the display, rotate the knob all the way to the
left and then to the right as described in step 2
and above.
* The delay time of an individual Effect Band can be set to a
maximum of 696msec. Using the Group setting, a maxi-
mum delay of 5890msec can be obtained by grouping all
8 Effect Bands together. (
→
page 16)
* The delay time can also be set by tapping the [EFFECT
BAND 1-8] button twice in tempo, after the Effect Band
has been selected. The delay time will be set to the tempo
at which the button is pressed.
* You can also tap the Footswitch twice in tempo to set the
delay time to the tempo at which the Footswitch was
tapped. (
→
page 22)
Содержание UD-Stomp
Страница 1: ......
Страница 32: ...Printed in Taiwan V839860 ...