background image

6

Your Yamaha timpani is equipped with a plastic head carefully mounted and adjusted at the factory.

However, new heads tend to stretch during shipping and storage, so it may be necessary to re-tune the

instrument before using. Please perform the following steps to check and, if necessary, readjust your

instrument.

3

If the heel of the pedal is fully lowered as in 

Fig.

C

, proceed with step 

5

.

If the pedal position is as shown in 

Fig. D

 or the

toe of the pedal is fully lowered, perform step 

4

first.

Initial Preparation

1

The area between the kettle edge and the inner

circle of the counter hoop is called the collar.

Please make sure that the width of this collar is

uniform, as shown in the illustration titled “Cor-

rect”.

Counter
hoop

Correct

Kettle
edge

Collar

Wrong

Counter
hoop

Kettle
edge

Collar

If the collar is not uniform (illustration titled

“Wrong”), keep the heel of the pedal fully de-

pressed as shown in 

Fig. C

, and align the head

and hoop as shown in the illustration titled “Cor-

rect”.

2

Make sure that the end of the wire tube is not

disengaged from the adjuster of the tuning indi-

cator as shown in 

Fig. A

. If it is disengaged, in-

sert it into the adjuster as shown in 

Fig. B

.

Adjuster

Fig. B

Fig. A

Wire tube

Fig. C

Fig. D

4

Fully depress the heel of the pedal as shown in

Fig. C

. Hold the pedal in this position, as it will

return otherwise.

Caution

Never place your fingers or foot into the mov-
ing parts or the space under the pedal or base.
Serious injury can result if fingers or feet be-
come pinched.

tp3100ea_en_om.6pm

08.2.5, 9:28 AM

6

Содержание TP-3123












Отзывы: