Yamaha T-50C Скачать руководство пользователя страница 80

Страница: 80 / 114

4-21

EMU00992

CHECKING POWER TRIM AND TILT
SYSTEM

Never get under the lower unit while it
is tilted, even when the tilt-support
lever is locked. Severe injury could
occur if the outboard accidentally falls.

Make sure no one is under the out-
board before performing this test.

Check the power trim and tilt unit for
any sign of oil leaks.

Operate each of the power trim and
tilt switches on remote control and
engine bottom cowling (If equipped)
to check that all switches work.

Tilt up the motor and check that the
trim and tilt rod

is pushed out com-

pletely.

Check that the trim and tilt rod is free
of corrosion or other flaws.

Operate the motor to trim and tilt
down. Check that the trim and tilt rod
operates smoothly.

NOTE:

If any operation is abnormal, consult a
Yamaha dealer.

Recommended fluid:

Yamaha power trim & tilt fluid or
ATF (DEXRON-

)

000965

62Y-9-1C-4 3/20/03 10:25 AM Page 22

Содержание T-50C



















































































































Результаты поиска

Содержание T-50C

Отзывы:

Yamaha T-50C, Руководство пользователя, Страница: 80 / 114

Результаты поиска

Содержание T-50C

Отзывы: