Yamaha T-50C страница 68 Скачать руководство пользователя

Страница: 68 / 114

4-9

EMU19380

MAINTENANCE CHART

Frequency of maintenance operations may be adjusted according to the operating con-
ditions, but the following table gives general guidelines. Refer to the sections in this
chapter for explanations of each owner-specific action.
The mark (

●

) indicates the check-ups which you may carry out yourself.

The mark (

) indicates work to be carried out by your Yamaha dealer.

NOTE:

When operating in salt water, turbid or muddy water, the engine should be flushed
with clean water after each use.

10 hours

50 hours

100 hours

200 hours

(1 month)

(3 months)

(6 months)

(1 year)

Spark plug(s)

Cleaning / adjustment /
replacement

●

Greasing points

Greasing

●

Gear oil

Change

●

Fuel system

Inspection

●

Fuel filter (can be
disassembled)

Inspection / cleaning

●

Fuel tank (Yamaha
portable tank)

Cleaning

●

Idling speed (carburetor
models)

Inspection / adjustment

●

Anode(s)

Inspection / replacement

●

Cooling water passages

Cleaning

●

Propeller and cotter pin

Inspection / replacement

●

Timing belt

Inspection / replacement

Battery

Inspection / charging

●

Throttle link / throttle cable
/ throttle pick-up timing

Inspection / adjustment

Shift link / shift cable

Inspection / adjustment

Thermostat

Inspection

Power trim and tilt unit

Inspection

Water pump

Inspection

Engine oil

Inspection / change

●

Oil filter (cartridge)

Change

Valve clearance (OHC,
OHV)

Inspection / adjustment

Cowling clamp

Inspection

●

Actions

Item

Initial

Every

62Y-9-1C-4 3/20/03 10:25 AM Page 10

Содержание T-50C



















































































































Результаты поиска

Содержание T-50C

Отзывы:

Похожие инструкции для T-50C

Бренды по названию

Популярные бренды

Yamaha T-50C, Руководство пользователя

Результаты поиска

Содержание T-50C

Отзывы:

Похожие инструкции для T-50C

Бренды по названию

Популярные бренды