Yamaha T-50C страница 58 Скачать руководство пользователя

Страница: 58 / 114

3-19

EMH60010

CRUISING IN OTHER

CONDITIONS

CRUISING IN SALT WATER

After operating in salt water, wash out the
cooling-water passages with fresh water
to prevent them from becoming clogged-
up with salt deposits.

NOTE:

Refer to cooling system flushing instruc-
tions in “TRANSPORTING AND STORING
OUTBOARD MOTOR”.

CRUISING IN TURBID WATER

It is strongly recommended that the
optional chromium-plated water-pump kit
be installed if the outboard is to be used
in turbid (muddy) water conditions.

EMU00303

PROCEDURE FOR TILTING DOWN

Power trim/tilt model

Push the power trim/tilt switch “UP”
until the engine is supported by the
tilt rod.

Release the tilt-support lever.

Push the power trim/tilt switch “DN”
(Down) to lower the engine to the
desired position.

000979

62Y-9-1C-3 3/20/03 10:23 AM Page 20

Содержание T-50C



















































































































Результаты поиска

Содержание T-50C

Отзывы:

Похожие инструкции для T-50C

Бренды по названию

Популярные бренды

Yamaha T-50C, Руководство пользователя

Результаты поиска

Содержание T-50C

Отзывы:

Похожие инструкции для T-50C

Бренды по названию

Популярные бренды