Yamaha T-50C страница 29 Скачать руководство пользователя | Manualshive

Страница: 29 / 114

background image

E

2-6

UP
DN

701034*

UP

DN

701035

EMU01331

Power Trim/Tilt Switch

The power trim/tilt adjusts the motor
angle in relation to the transom. The
power trim/tilt switch is located on the
remote control lever grip. Pushing the
switch “UP” trims the motor up, then tilts
the motor up. Pressing the switch “DN”
tilts the motor down and trims the motor
down. When the switch button is
released, the motor will stop in its current
position.

NOTE:

Refer to the sections “ADJUSTING TRIM
ANGLE” and “TILTING UP/DOWN” in
Chapter 3 for instructions on usage.

EMU01155

Throttle Friction Adjusting Screw

A friction device in the remote control box
provides adjustable resistance to move-
ment of the remote control lever, and can
be set according to operator preference.
An adjusting screw is located on the front
of the remote control box.

w

Do not overtighten the friction adjusting
screw. If there is too much resistance, it
may be difficult to move the lever, which
could result in an accident.

Resistance

Screw

Increase

Turn clockwise

Decrease

Turn counterclockwise

62Y-9-1C-2 3/20/03 10:22 AM Page 7

«
...
27
28
29
30
31
...
»

Содержание T-50C



















































































































Отзывы:

Нет отзывов

Похожие инструкции для T-50C

Бренд: Larcan Страницы: 13

The Prelude PC-200

Бренд: Harman Kardon Страницы: 6

Бренд: Harman Kardon Страницы: 16

Бренд: Harman Kardon Страницы: 32

Бренд: Harman Kardon Страницы: 8

Бренд: Harman Kardon Страницы: 26

Бренд: Harman Kardon Страницы: 11

Бренд: Harman Kardon Страницы: 31

Бренд: Harman Kardon Страницы: 18

Бренд: Harman Kardon Страницы: 29

Бренд: Harman Kardon Страницы: 48

Бренд: NAD Страницы: 2

Бренд: Warfedale Pro Страницы: 12

Бренд: D.A.S. Страницы: 11

Бренд: TC Electronic Страницы: 45

Бренд: Teac Страницы: 15

belles Soloist 3

Бренд: Power Modules Страницы: 7

Бренд: Warwick Страницы: 11

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды