Yamaha T-50 Скачать руководство пользователя страница 79 | Manualshive

Страница: 79 / 116

background image

Operation

73

3. Pull the tilt support lever toward you to

support the engine.

WARNING! After

tilting the outboard motor, be sure to
support it with the tilt support knob or
tilt support lever. Otherwise the out-
board motor could fall back down
suddenly if oil in the power trim and
tilt unit or in the power tilt unit loses
pressure.

[EWM00262]

NOTICE:

Do not use

the tilt support lever or knob when
trailering the boat. The outboard mo-

tor could shake loose from the tilt
support and fall. If the motor cannot
be trailered in the normal running po-
sition, use an additional support de-
vice to secure it in the tilt position.
For more detailed information, see
page 76.

[ECM01641]

4. Models equipped with trim rods: Once

the outboard motor is supported with the
tilt support lever, press the power trim
and tilt switch “

” (down) to retract the

trim rods.

NOTICE:

Make sure that the

trim rods retracts completely during
mooring. This protects the rods from
marine growth and corrosion, which
could damage the power trim and tilt
mechanism.

[ECM00252]

EMU33121

Procedure for tilting down (power
trim and tilt models)

1. Push the power trim and tilt switch “

”

(up) until the outboard motor is support-
ed by the tilt rod and the tilt support lever
becomes free.

2. Release the tilt support lever.

UP

ZMU07920

ZMU03640

6C1-9-3B-1E0.book 73 ページ２０１２年１１月１９日　月曜日　午前１０時３５分

«
...
77
78
79
80
81
...
»

Содержание T-50





















































































































Отзывы:

Нет отзывов

Похожие инструкции для T-50

Бренд: Octave Страницы: 23

Бренд: VAC Страницы: 10

Бренд: Halcro Страницы: 2

Бренд: Kramer Страницы: 15

Бренд: MGC Страницы: 2

Бренд: Fenton Страницы: 20

Бренд: Creek Audio Страницы: 4

Бренд: JET CITY AMPLIFICATION Страницы: 12

Бренд: Revox Страницы: 9

Бренд: Demeter Amplification Страницы: 2

Бренд: Toa Страницы: 16

Mono Amp JPA1150M

Бренд: Jensen Страницы: 19

Бренд: SpeakerCraft Страницы: 8

Бренд: Sound Choice Страницы: 16

Бренд: Decware Страницы: 18

Бренд: Rainbow Страницы: 19

Troubadour T15II

Бренд: Ibanez Страницы: 4

Бренд: Mutant Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды