Yamaha T-50 Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 116

background image

Safety information

4

go to boatus.org.

For Canada

All operators of pleasure craft must illustrate
competency by means of a Pleasure Craft
Operators Card with the exception of Per-
sonal Water Craft used for rental purposes
which require a rental checklist be complet-
ed. Pleasure Craft Operators Cards can be
obtained following the completion of a com-
petency course, with an on-line option. De-
tails can be found on Transport Canada’s
website. www.tc.gc.ca

EMU33880

Passenger training

Make sure at least one other passenger is
trained to operate the boat in the event of an
emergency.

EMU33890

Boating safety publications

Be informed about boating safety. Additional
publications and information can be obtained
from many boating organizations.

EMU33590

Laws and regulations

Know the marine laws and regulations where
you will be boating- and obey them. Several
sets of rules prevail according to geographic
location, but all are basically the same as the
International Rules of the Road. The rules
presented in the following section are con-
densed- and have been provided for your
convenience only.
Contact the U.S. Coast Guard, the National
Association of State Boating Law Adminis-
trators, or your local Power Squadron for a
complete set of rules governing the waters in
which you will be using your boat.

EMU44180

Boating organizations

The following organizations provide boating
safety training and information about boating
safety and laws.

In the U.S.A.
United States Coast Guard

Consumer Affairs Staff (G-BC)
Office of Boating, Public, and Consumer Af-
fairs
U.S. Coast Guard Headquarters
Washington, D.C. 20593-0001
http://www.uscgboating.org/

United States Power Squadrons

1-888-FOR-USPS (1-888-367-8777)
http://www.usps.org/

Boat Owners Association of The United
States

1-800-336-BOAT (1-800-336-2628)
http://www.boatus.com/

National Association of State Boating
Law Administrators (NASBLA)

1500 Leestown Road, Suite 330
Lexington, KY 40511 859-225-9497
http://www.nasbla.org/

National Marine Manufacturers Associa-
tion (NMMA)

200 East Randolph Drive
Suite 5100
Chicago, IL 60601
http://www.nmma.org/

Marine Retailers Association of America

155 N. Michigan Ave. Chicago,
IL 60304
http://www.mraa.com/

In the Canada
National Marine Manufacturers Associa-
tion Canada

14 McEwan Drive

6C1-9-3B-1E0.book 4 ページ２０１２年１１月１９日　月曜日　午前１０時３５分

«
...
8
9
10
11
12
...
»

Содержание T-50





















































































































Отзывы:

Нет отзывов

Похожие инструкции для T-50

Бренд: NAD Страницы: 2

Бренд: NAD Страницы: 33

Бренд: TDT Страницы: 81

Бренд: YORKVILLE Страницы: 12

Бренд: YORKVILLE Страницы: 8

SERVOSTAR 600 Series

Бренд: Kollmorgen Seidel Страницы: 68

Бренд: SMSL Страницы: 8

Бренд: Jolida Страницы: 17

Бренд: ZENEC Страницы: 30

Бренд: Samson Страницы: 2

Бренд: MTX Страницы: 14

Бренд: Blackstar Страницы: 1

Бренд: JDS Labs Страницы: 7

Бренд: ValveTrain Amplification Страницы: 7

ZOTL40 Reference

Бренд: Linear Tube Audio Страницы: 8

Бренд: bent audio Страницы: 11

Бренд: Advance Paris Страницы: 28

Valvestate VS100

Бренд: Marshall Amplification Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды