manualshive.com logo in svg

Yamaha T-50, Руководство пользователя

Поделиться
Скачать
Yamaha T-50 Скачать руководство пользователя страница 91

Maintenance

85

F50HB, F60HB, F70HA

EMU28958

Cleaning and adjusting spark plug

The spark plug is an important engine com-
ponent and is easy to inspect. The condition
of the spark plug can indicate something
about the condition of the engine. For exam-
ple, if the center electrode porcelain is very
white, this could indicate an intake air leak or
carburetion problem in that cylinder. Do not
attempt to diagnose any problems yourself.
Instead, take the outboard motor to a
Yamaha dealer. You should periodically re-

move and inspect the spark plug because
heat and deposits will cause the spark plug
to slowly break down and erode.
1. Remove the spark plug caps from the

spark plugs.

2. Remove the spark plug. If electrode ero-

sion becomes excessive, or if carbon
and other deposits are excessive, you
should replace the spark plug with an-
other of the correct type. 

WARNING!

When removing or installing a spark
plug, be careful not to damage the in-

ZMU07924

6C1-9-3B-1E0.book  85 ページ  ２０１２年１１月１９日　月曜日　午前１０時３５分

Содержание T-50





















































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды