Yamaha STAR XV19CSX Скачать руководство пользователя | Manualshive

Страница: 78 / 96

background image

MOTORCYCLE CARE AND STORAGE

7-4

7

3. Perform the following steps to pro-

tect the cylinders, piston rings, etc.
from corrosion.

a. Remove the spark plug caps

and spark plugs.

b. Pour a teaspoonful of engine oil

into each spark plug bore.

c. Install the spark plug caps onto

the spark plugs, and then place
the spark plugs on the cylinder
head so that the electrodes are
grounded. (This will limit spark-
ing during the next step.)

d. Turn the engine over several

times with the starter. (This will
coat the cylinder walls with oil.)

e. Remove the spark plug caps

from the spark plugs, and then
install the spark plugs and the
spark plug caps.

WARNING

EWA10950

To prevent damage or injury from
sparking, make sure to ground the
spark plug electrodes while turning
the engine over.

4. Lubricate all control cables and the

pivoting points of all levers and
pedals as well as of the side-
stand/centerstand.

5. Check and, if necessary, correct

the tire air pressure, and then lift
the motorcycle so that both of its
wheels are off the ground. Alterna-
tively, turn the wheels a little every
month in order to prevent the tires
from becoming degraded in one
spot.

6. Cover each muffler outlet with a

plastic bag to prevent moisture
from entering them.

7. Remove the battery and fully

charge it. Store it in a cool, dry
place and charge it once a month.
Do not store the battery in an ex-
cessively cold or warm place [less
than 0 °C (30°F) or more than 30
°C (90°F)]. For more information
on storing the battery, see page
6-25.

NOTE:

Make any necessary repairs before
storing the motorcycle.

U29S10E0.book Page 4 Friday, May 18, 2007 1:53 PM

«
...
76
77
78
79
80
...
»

Содержание STAR XV19CSX

































































































Отзывы:

Нет отзывов

Похожие инструкции для STAR XV19CSX

Speedglas G5-02

Бренд: 3M Страницы: 17

Speedglas 9100 MP

Бренд: 3M Страницы: 72

Бренд: 3M Страницы: 84

Бренд: Can-Am Страницы: 16

Бренд: Can-Am Страницы: 254

Бренд: hepco & becker Страницы: 4

MAESTRO EDGE 125 PROGRAMMED FI

Бренд: HERO Страницы: 84

Бренд: R&G Страницы: 9

SEMIFAIRING BATWING SML TOURING

Бренд: PUIG Страницы: 3

Бренд: Can-Am Страницы: 196

Бренд: Honda Страницы: 190

Бренд: GAS GAS Страницы: 107

Бренд: KTM Страницы: 90

Бренд: Bajaj Страницы: 39

Бренд: hepco & becker Страницы: 3

Бренд: LAS Страницы: 22

Бренд: hepco & becker Страницы: 3

Бренд: hepco & becker Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды