Yamaha STAR XV19CSX Скачать руководство пользователя

Страница: 47 / 96

PERIODIC MAINTENANCE AND MINOR REPAIR

6-6

Front fork

• Check operation and for oil leak-

age.

• Replace if necessary.

√

Shock absorber as-
sembly

• Check operation and for oil leak-

age.

• Replace if necessary.

√

Rear suspension
link pivots

• Apply lithium-soap-based grease

lightly.

√

Engine oil

• Change (warm engine before

draining).

√

Engine oil filter car-
tridge

• Replace.

√

Transfer case oil

• Check for leakage.
• Change at initial 600 mi (1000

km) or 1 month, and thereafter
every 16000 mi (25000 km) or 24
months.

Change.

√

Change.

Front and rear brake
switches

• Check operation.

√

Control cables

• Apply Yamaha chain and cable

lube or engine oil SAE 10W-30
thoroughly.

√

Throttle grip hous-
ing and cable

• Check operation and free play.
• Adjust the throttle cable free play

if necessary.

• Lubricate the throttle grip housing

and cable.

√

No.

ITEM

ROUTINE

INITIAL

ODOMETER READINGS

600 mi

(1000 km)

1 month

4000 mi

(7000 km)

6 months

8000 mi

(13000 km)

12 months

12000 mi

(19000 km)

18 months

16000 mi

(25000 km)

24 months

20000 mi

(31000 km)

30 months

U29S10E0.book Page 6 Friday, May 18, 2007 1:53 PM

Содержание STAR XV19CSX

































































































Результаты поиска

Содержание STAR XV19CSX

Отзывы:

Похожие инструкции для STAR XV19CSX

Бренды по названию

Популярные бренды

Yamaha STAR XV19CSX, Руководство пользователя

Результаты поиска

Содержание STAR XV19CSX

Отзывы:

Похожие инструкции для STAR XV19CSX

Бренды по названию

Популярные бренды