manualshive.com logo in svg

Yamaha STAR XV19CSX, Руководство пользователя

Поделиться
Скачать
Yamaha STAR XV19CSX Скачать руководство пользователя страница 20

INSTRUMENT AND CONTROL FUNCTIONS

3-3

3

●

two tripmeters (which show the
distance traveled since they were
last set to zero)

●

a fuel reserve tripmeter (which
shows the distance traveled on the
fuel reserve)

●

a clock

●

a self-diagnosis device

●

a brightness control mode

NOTE:

Be sure to turn the key to “ON” before
using the “SELECT” and reset switch-
es, except for setting the brightness
control mode.

Speedometer

When the key is turned to “ON”, the
speedometer needle will sweep once
across the speed range and then return
to zero in order to test the electrical cir-
cuit.

Fuel gauge

The fuel gauge indicates the amount of
fuel in the fuel tank. The needle moves
towards  “E” (Empty) as the fuel level
decreases. When the needle reaches
“E”, approximately 3.2 L (0.85 US gal)
(0.70 Imp.gal) remain in the fuel tank. If
this occurs, refuel as soon as possible.
When the key is turned to “ON”, the fuel
gauge needle will sweep once across
the fuel level range and then return to
the current amount in order to test the
electrical circuit.

NOTE:

●

Do not allow the fuel tank to empty
itself completely.

1. “SELECT” switch

1. Reset switch

1. Speedometer

10

0

20

30

40

50

60

70

80

90

100

110

120

130

140

MPH

km/h

220

220

200

200

160

60

180

80

140

40

120

20

100

00

80

80

60

60

40

40

20

20

0

1

1. Fuel gauge

U29S10E0.book  Page 3  Friday, May 18, 2007  1:53 PM

Содержание STAR XV19CSX

































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды