Yamaha STAR XV19CSX Скачать руководство пользователя | Manualshive

Страница: 72 / 96

background image

PERIODIC MAINTENANCE AND MINOR REPAIR

6-31

6

EAU24321

Replacing a license plate light
bulb

1. Remove the license plate light unit

by removing the nuts, washers and
rubber dampers.

2. Remove the license plate light lens

by removing the nuts and washers.

3. Remove the defective bulb by pull-

ing it out.

4. Insert a new bulb into the socket.
5. Install the license plate light lens

by installing the washers and the
nuts.

6. Install the license plate light unit by

installing the rubber dampers,
washers and the nuts.

EAU24350

Supporting the motorcycle

Since this model is not equipped with a
centerstand, follow these precautions
when removing the front and rear
wheel or performing other maintenance
requiring the motorcycle to stand up-
right. Check that the motorcycle is in a
stable and level position before starting
any maintenance. A strong wooden
box can be placed under the engine for
added stability.

To service the front wheel

1. Stabilize the rear of the motorcycle

by using a motorcycle stand or, if
an additional motorcycle stand is
not available, by placing a jack un-
der the frame in front of the rear
wheel.

2. Raise the front wheel off the

ground by using a motorcycle
stand.

To service the rear wheel

Raise the rear wheel off the ground by
using a motorcycle stand or, if a motor-
cycle stand is not available, by placing

1. Nut

2. Washer
3. Rubber damper

4. License plate light unit

1. Nut
2. Washer

3. Bulb

4. License plate light lens

U29S10E0.book Page 31 Friday, May 18, 2007 1:53 PM

«
...
70
71
72
73
74
...
»

Содержание STAR XV19CSX

































































































Отзывы:

Нет отзывов

Похожие инструкции для STAR XV19CSX

Бренд: Dakota Digital Страницы: 38

Бренд: Victory Motorcycles Страницы: 332

H-X-ADV-07-01-AL

Бренд: SRC Страницы: 6

Бренд: Cobra Страницы: 80

Бренд: MOTO GUZZI Страницы: 266

Бренд: Suzuki Страницы: 165

Бренд: Thunderbike Страницы: 7

Бренд: Honda Страницы: 330

Бренд: N-Com Страницы: 32

Бренд: yasuni Страницы: 9

Бренд: Arai Страницы: 2

Бренд: Royal Enfield Страницы: 110

Бренд: Malaguti Страницы: 272

Бренд: Yamaha Страницы: 93

Бренд: Yamaha Страницы: 114

Бренд: Yamaha Страницы: 100

Бренд: Yamaha Страницы: 100

Бренд: Yamaha Страницы: 102

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды