Yamaha Star 2010 страница 65 Скачать руководство пользователя | Manualshive

Страница: 65 / 104

background image

PERIODIC MAINTENANCE AND ADJUSTMENT

7-22

7

Before riding, check that the brake fluid
is above the minimum level mark and
replenish if necessary. A low brake fluid
level may indicate worn brake pads
and/or brake system leakage. If the
brake fluid level is low, be sure to check
the brake pads for wear and the brake
system for leakage.
Observe these precautions:

●

When checking the fluid level,
make sure that the top of the brake
fluid reservoir is level.

●

Use only the recommended quality
brake fluid, otherwise the rubber
seals may deteriorate, causing
leakage and poor braking perfor-
mance.

●

Refill with the same type of brake
fluid. Mixing fluids may result in a
harmful chemical reaction and
lead to poor braking performance.

●

Be careful that water does not en-
ter the brake fluid reservoir when
refilling. Water will significantly
lower the boiling point of the fluid
and may result in vapor lock.

●

Brake fluid may deteriorate paint-
ed surfaces or plastic parts. Al-
ways clean up spilled fluid
immediately.

●

As the brake pads wear, it is nor-
mal for the brake fluid level to grad-
ually go down. However, if the
brake fluid level goes down sud-
denly, have a Yamaha dealer
check the cause.

EAU22731

Changing the brake fluid

Have a Yamaha dealer change the
brake fluid at the intervals specified in
the TIP after the periodic maintenance
and lubrication chart. In addition, have
the oil seals of the master cylinders and
calipers as well as the brake hoses re-
placed at the intervals listed below or
whenever they are damaged or leak-
ing.

●

Oil seals: Replace every two
years.

●

Brake hoses: Replace every four
years.

Recommended brake fluid:

DOT 4

U5S614E0.book Page 22 Friday, July 9, 2010 9:18 AM

«
...
63
64
65
66
67
...
»

Содержание Star 2010









































































































Отзывы:

Нет отзывов

Похожие инструкции для Star 2010

Бренд: KEDO Страницы: 2

Бренд: KEDO Страницы: 3

Бренд: KEDO Страницы: 2

ALK.00.733.15000/B

Бренд: SW-Motech Страницы: 14

Бренд: Ducati Страницы: 128

Бренд: A.J.S. Страницы: 104

Бренд: KTM Страницы: 13

Бренд: X-lite Страницы: 96

Rally Pack Value Series

Бренд: Dowco Страницы: 3

Outlander 6x6 450 XU+ 2022

Бренд: Can-Am Страницы: 226

Бренд: R&G Страницы: 17

Бренд: R&G Страницы: 18

Бренд: R&G Страницы: 17

Бренд: Yamaha Страницы: 80

Бренд: Yamaha Страницы: 278

Бренд: APRILIA Страницы: 168

Бренд: Rockford Fosgate Страницы: 8

Бренд: Rockford Fosgate Страницы: 17

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды