Yamaha Star 2010 Скачать руководство пользователя

Страница: 55 / 104

PERIODIC MAINTENANCE AND ADJUSTMENT

7-12

4. If the engine oil is below the mini-

mum level mark, add sufficient oil
of the recommended type to raise
it to the correct level.

To change the engine oil (with or
without oil filter cartridge replace-
ment)

1. Place the vehicle on a level sur-

face.

2. Start the engine, warm it up for

several minutes, and then turn it
off.

3. Place an oil pan under the engine

to collect the used oil.

4. Remove the engine oil filler cap,

the engine oil drain bolt and its
gasket to drain the oil from the
crankcase.

TIP

Skip steps 5–7 if the oil filter cartridge is
not being replaced.

5. Remove the oil filter cartridge with

an oil filter wrench.

TIP

An oil filter wrench is available at a
Yamaha dealer.

6. Apply a thin coat of clean engine

oil to the O-ring of the new oil filter
cartridge.

1. Engine oil filler cap
2. Engine oil level check window

3. Maximum level mark

4. Minimum level mark

1. Engine oil drain bolt
2. Gasket

1. Oil filter cartridge
2. Oil filter wrench

U5S614E0.book Page 12 Friday, July 9, 2010 9:18 AM

Содержание Star 2010









































































































Результаты поиска

Содержание Star 2010

Отзывы:

Похожие инструкции для Star 2010

Бренды по названию

Популярные бренды

Yamaha Star 2010, Руководство пользователя

Результаты поиска

Содержание Star 2010

Отзывы:

Похожие инструкции для Star 2010

Бренды по названию

Популярные бренды