manualshive.com logo in svg

Yamaha Star 2010, Руководство пользователя

Поделиться
Скачать
Yamaha Star 2010 Скачать руководство пользователя страница 52

PERIODIC MAINTENANCE AND ADJUSTMENT

7-9

7

EAU18751

Removing and installing the 
panel 

The panel shown needs to be removed
to perform some of the maintenance
jobs described in this chapter. Refer to
this section each time the panel needs
to be removed and installed.

EAU48560

Panel A

To remove the panel
Remove the quick fastener, and then
pull the panel off as shown.

To install the panel
Place the panel in the original position,
and then install the quick fastener.

EAU42431

Checking the spark plugs 

The spark plugs are important engine
components, which are easy to check.
Since heat and deposits will cause any
spark plug to slowly erode, the spark
plugs should be removed and checked
in accordance with the periodic mainte-
nance and lubrication chart. In addition,
the condition of the spark plugs can re-
veal the condition of the engine.

To remove a spark plug

1. Remove the appropriate spark

plug cover (rear right or front left)
by removing the bolts.

2. Remove the spark plug cap.

1. Panel A

1

1. Panel A
2. Quick fastener

1. Panel A

1

2

1

1. Spark plug cover

2. Bolt

U5S614E0.book  Page 9  Friday, July 9, 2010  9:18 AM

Содержание Star 2010









































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды