Yamaha Star 2010 Скачать руководство пользователя

Страница: 77 / 104

PERIODIC MAINTENANCE AND ADJUSTMENT

7-34

EAU42484

Replacing the license plate
light bulb

1. Remove the license plate light cov-

er by removing the bolts.

2. Pull the license plate light unit up

as shown.

3. Remove the license plate light

socket (together with the bulb) by
turning it counterclockwise, and
then pulling it out.

4. Remove the burnt-out bulb by pull-

ing it out from the socket.

5. Insert a new bulb into the socket.

6. Install the socket (together with the

bulb) by pushing it in and turning it
clockwise until it stops.

7. Place the license plate light unit in

the original position, and then in-
stall the license plate light cover by
installing the bolts.

1. License plate light cover

2. Bolt

1. License plate light unit

1. License plate light bulb socket

1. License plate light bulb

U5S614E0.book Page 34 Friday, July 9, 2010 9:18 AM

Содержание Star 2010









































































































Результаты поиска

Содержание Star 2010

Отзывы:

Похожие инструкции для Star 2010

Бренды по названию

Популярные бренды

Yamaha Star 2010, Руководство пользователя

Результаты поиска

Содержание Star 2010

Отзывы:

Похожие инструкции для Star 2010

Бренды по названию

Популярные бренды