8
To Remove the 275L Nose Cone and charge the Battery
Pod, User MUST follow these instructions to avoid any
injury.
1. ALWAYS ensure that the Master Switch is in OFF position.
2. ALWAYS ensure that the 275L is out of the water, dry and
placed in a dry area.
3. Pull the four Latches down and remove the nose cone by
using the left and right Latches to break the seal if
necessary (see Fig. 11 and Fig. 12) and jump to Step 9.
4. If the nose-cone cannot be opened by pressing the
latches, replace the Retractable rubber handle on the
SEASCOOTER™ 275L. (see Fig. 13)
5. Release the Vent plug on top of the Nose Cone.
6. Pull the rubber ring through the retractable rubber handle
and attach both ends around the top and bottom latch
hinge as shown in Fig. 13.
7. Screw the pump nozzle to the vent chamber and pump air
in until the Nose Cone pops off
(see Fig. 14).
IMPORTANT
: ALWAYS attach the Rubber Ring before
using the pump. The Nose Cone can pop off and cause
injury if the Rubber Ring is not attached and tighly
secured.
8. Remove the Rubber Ring and remove the Nose Cone
(see Fig. 15).
9. Allow two minutes for any gases to dissipate.
10. Take out the Battery Pod from the unit.
11. Connect the Battery Pod to the Charging Base.
(see Fig. 16)
12. Plug the Charging Base into the mains, and turn on the
supply.
13. Charging will take around 12-14 hours for a fully
discharged battery. When the Battery Pod is charging, the
RED LED light on the Battery Pod remains flashing.
When the battery is fully charged, the GREEN LED
flashes. (see Fig. 16)
14. Unplug the Charging Base from the electrical socket/plug.
15. Allow battery to stand for 30 minutes before using it.
16. Unplug the Battery Pod from the Charging Base.
17. When ready to use, reconnect to the unit in the correct
position. (see Fig. 17)
18. MAKE SURE the O-ring Seals and sealing surfaces are
clean and fully lubricated
with the supplied grease
EVERYTIME (you can also
buy this at your local
hardware store) before
replacing the Nose Cone.
(see Fig. 18)
19. Ensure the Vent O Ring is
fitted correctly into the
groove and fully lubricated
with the supplied grease. (see
Fig. 18)
20. MAKE SURE to screw in the
Vent Plug to seal the vent.
21. Replace the Nose Cone and
close the Latches.
Getting Started
10. Always set the Master Switch to the OFF position when
it is out of the water. (see fig.6)
Use of variable speed
Your SEASCOOTER™ 275L features three speeds. To
change the speed, pull and the Triggers repeatedly to switch
between low, middle and high speed. See steps 5, 6 and 7
on page 8 and page 9.
Fig.3
LED Battery
Status Indicator
Slide the Master Switch
down to "ON" position
When using the SEASCOOTER™ 275L for the first time,
the battery needs to be charged. Follow the the Battery
Instruction on pages 12, 13, 14 and 15 and charging
instructions on pages 16 and 17.
Your SEASCOOTER™ 275L can be used for swimming,
snorkeling or diving up to 40m/130ft (by qualified divers).
To use the SEASCOOTER
™
275L follow these
instructions.
1. Charge the battery and install just before use.
2. Place the SEASCOOTER™ 275L into the water and rock
gently to release trapped air.
3. Adjust buoyancy to suit conditions and personal
preferences - see page 10, Adjustable Buoyancy.
4. When ready to set off, switch the Master Switch to the
ON position (see fig.3).
5.
For US version
: Pull and hold the left or the right trigger
to start the propeller (see fig.4). The SEASCOOTER™
275L will accelerate up to speed 1.
For EU version
: Pull and hold both Triggers to
start the Propeller (see fig.4). The SEASCOOTER™
275L will accelerate up to speed 1.
(There is a short delay before the Propeller begins to
rotate).
Fig.4
Triggers
Master switch
is ON.
6. To increase speed at any time, simply pulse the triggers
off and on again within half a second. The
SEASCOOTER™ 275L will accelerate up to the next
speed. Make sure that only one Trigger is being used at a
time.
7. When at speed 3, further pulses will have no effect.
8. To stop the Propeller, simply release the Trigger(s).
9. Maintain proper posture to achieve the maximum speed
when using the SEASCOOTER™ 275L – see fig.5 for the
correct position of the SEASCOOTER™ 275L when using
it.
9
Fig.5
GOOD
BEST
