Technical Specifications
26
*Normal Use
The definition of normal use is based on the average general time
of use the user activates the seascooter in the water.
∆
Continuous Use
The definition of continuous use is based on a fully charged battery
whereby the seascooter is used continuously in the water without
stopping.
12.6 inches x 12.6 inches x 28 inches
(320 x 320 x 710 mm)
Unit Dimensions
Unit Weight
32.4 lb (14.7 kg) (with rechargeable battery)
14.3 lb (6.5 kg) (without rechargeable battery)
Battery Type
1 x 12V / 24Ah rechargeable battery
Battery Life /
Fully Charged
*Run up to 2 hours with normal use
∆
Continuous use up to 50 minutes (high speed)
Depth rating
40m/130ft
Speed
Up to 3.3 mph (5.3 km/
h)
To Remove the 275L Nose Cone and charge the Battery
Pod, User MUST follow these instructions to avoid any
injury.
1. ALWAYS ensure that the Master Switch is in OFF position.
2. ALWAYS ensure that the 275L is out of the water, dry and
placed in a dry area.
3. Pull the four Latches down and remove the nose cone by
using the left and right Latches to break the seal if
necessary (see Fig. 11 and Fig. 12) and jump to Step 9.
4. If the nose-cone cannot be opened by pressing the
latches, replace the Retractable rubber handle on the
SEASCOOTER™ 275L. (see Fig. 13)
5. Release the Vent plug on top of the Nose Cone.
6. Pull the rubber ring through the retractable rubber handle
and attach both ends around the top and bottom latch
hinge as shown in Fig. 13.
7. Screw the pump nozzle to the vent chamber and pump air
in until the Nose Cone pops off
(see Fig. 14).
IMPORTANT
: ALWAYS attach the Rubber Ring before
using the pump. The Nose Cone can pop off and cause
injury if the Rubber Ring is not attached and tighly
secured.
8. Remove the Rubber Ring and remove the Nose Cone
(see Fig. 15).
9. Allow two minutes for any gases to dissipate.
10. Take out the Battery Pod from the unit.
11. Connect the Battery Pod to the Charging Base.
(see Fig. 16)
12. Plug the Charging Base into the mains, and turn on the
supply.
13. Charging will take around 12-14 hours for a fully
discharged battery. When the Battery Pod is charging, the
RED LED light on the Battery Pod remains flashing.
When the battery is fully charged, the GREEN LED
flashes. (see Fig. 16)
14. Unplug the Charging Base from the electrical socket/plug.
15. Allow battery to stand for 30 minutes before using it.
16. Unplug the Battery Pod from the Charging Base.
17. When ready to use, reconnect to the unit in the correct
position. (see Fig. 17)
18. MAKE SURE the O-ring Seals and sealing surfaces are
clean and fully lubricated
with the supplied grease
EVERYTIME (you can also
buy this at your local
hardware store) before
replacing the Nose Cone.
(see Fig. 18)
19. Ensure the Vent O Ring is
fitted correctly into the
groove and fully lubricated
with the supplied grease. (see
Fig. 18)
20. MAKE SURE to screw in the
Vent Plug to seal the vent.
21. Replace the Nose Cone and
close the Latches.
US & CANADA MARKET ONLY
Toll Free (US) : 1-800-678-7873
www.yamahaseascooters.com
(US & CANADA MARKET ONLY)
For more information on
Seascooter
™
Products
(Warranty, Customer Care / Maintenance,
Parts & Battery Purchase)
PLEASE VISIT
www.yamahaseascooters.com
Please visit our website at www.yamahaseascooters.com to find out your local distributor.
Yamaha, the Crossed Tuning Fork Design, and any likeness thereof are trademarks of
Yamaha Motor Corp. U.S.A. and Yamaha Motor Co., Ltd. (“Yamaha”) used
under license by Sport Dimension Inc. www.yamaha-motor.com.
This Product is not manufactured by Yamaha. For consumer purposes,
please contact Sport Dimension Inc. at 1-800-678-7873.
All corresponding specification appear in this manual are correct at the time of printing.
For the latest updates and further information on the complete range of the Seascooter™,
PLEASE VISIT www.yamahaseascooters.com
