• ALWAYS remove the battery pod from SEASCOOTER™
immediately after use.
• DO NOT STORE BATTERY POD IN SEASCOOTER
• DO NOT leave the Seascooter in the water. Always take the
unit out of water when not in use.
Washing and Care
• Always rinse the SEASCOOTER™ in fresh water and
allow it to dry before storage immediately after use.
• To clean the SEASCOOTER™ do not use detergents,
only use a damp cloth to wipe the unit clean.
• The Battery Housing interior should be kept dry at all
times.
• If the Battery Housing interior gets wet, see page 23,
Accidental Flooding for procedure.
• Always store your SEASCOOTER™ vertically when not
in use to prevent deformation of the Propeller Nozzle.
Buying Parts
Additional Battery Pods and Charging Bases can be
purchased separately. Contact your local Customer
service center/ distributor to purchase them.
To Remove the 275L Nose Cone and charge the Battery
Pod, User MUST follow these instructions to avoid any
injury.
1. ALWAYS ensure that the Master Switch is in OFF position.
2. ALWAYS ensure that the 275L is out of the water, dry and
placed in a dry area.
3. Pull the four Latches down and remove the nose cone by
using the left and right Latches to break the seal if
necessary (see Fig. 11 and Fig. 12) and jump to Step 9.
4. If the nose-cone cannot be opened by pressing the
latches, replace the Retractable rubber handle on the
SEASCOOTER™ 275L. (see Fig. 13)
5. Release the Vent plug on top of the Nose Cone.
Trouble Shooting
3. Disconnect and
remove the Battery
Pod - see page 15,
step 1 - 10.
4. Unscrew the twelve
Grille screws as
shown in
fig.20
to
remove the Inner
Nozzle and Propeller
Nozzle.
5.
While holding the
Propeller, use an M6
socket wrench to
remove the nut from
the Propeller shaft as shown in
fig.21.
6. Slide the Propeller off the shaft, taking care not to lose
the drive pin or washers.
7. Remove the blockage from the Propeller or Propeller
Shaft.
8. Replace the drive pin (if removed),
see fig.22
, and
Propeller. Turn the Propeller slowly until you locate the
pin and push the Propeller fully on.
Fig.20
x 12
1. Take the SEASCOOTER™ 275L out from the water.
2. Make sure the Master Switch is in the OFF position.
Opening the grilles to remove obstruction
Unit does not function
If the Propeller does not start when the triggers are
pressed, make sure:
1. The Master Switch is ON (see fig.3)
2. The Battery Pod is fully charged. (see page 15, charging
the Battery Pod)
3. The battery compartment is dry.
Blocked Propeller
If the Propeller becomes blocked, it will be necessary to
open the Protective Grilles to remove the obstacle.
UNDER NORMAL USE the grilles must not be opened.
NEVER turn ON the propeller when it is blocked, it will
cause serious damage to the gear box.
9. Replace the washer and nut and tighten with the
socket wrench while holding the Propeller, make sure it
is securely fastened.
(see fig.23)
10. Replace the Front Grille and Propeller Nozzle.
11. Install the Battery Pod and replace the Nose Cone
when ready for use.
Sand or Grit on O-ring Seal
Ensure that sand/grit does not get on the seals as Correct
maintenance and care is essential. To remove sand or grit
from the O-ring Seal, rinse the O-ring Seals in fresh water
and apply fresh lubricant. If there is sand inside the Battery
Housing, gently brush the sand from the unit, take care not
to scratch the sealing surfaces.
If an O-ring Seal is damaged, replace it with a new one
(see fig.1, item18) and apply fresh lubricant before use.
Warning!
Crushing / Cutting Hazard
Before opening the grille for maintenance purpose, make
sure the master switch is in off position, and the battery is
disconnected.
21
20
6. Pull the rubber ring through the retractable rubber handle
and attach both ends around the top and bottom latch
hinge as shown in Fig. 13.
7. Screw the pump nozzle to the vent chamber and pump air
in until the Nose Cone pops off
(see Fig. 14).
IMPORTANT
: ALWAYS attach the Rubber Ring before
using the pump. The Nose Cone can pop off and cause
injury if the Rubber Ring is not attached and tighly
secured.
8. Remove the Rubber Ring and remove the Nose Cone
(see Fig. 15).
9. Allow two minutes for any gases to dissipate.
10. Take out the Battery Pod from the unit.
11. Connect the Battery Pod to the Charging Base.
(see Fig. 16)
12. Plug the Charging Base into the mains, and turn on the
supply.
13. Charging will take around 12-14 hours for a fully
discharged battery. When the Battery Pod is charging, the
RED LED light on the Battery Pod remains flashing.
When the battery is fully charged, the GREEN LED
flashes. (see Fig. 16)
14. Unplug the Charging Base from the electrical socket/plug.
15. Allow battery to stand for 30 minutes before using it.
16. Unplug the Battery Pod from the Charging Base.
17. When ready to use, reconnect to the unit in the correct
position. (see Fig. 17)
18. MAKE SURE the O-ring Seals and sealing surfaces are
clean and fully lubricated
with the supplied grease
EVERYTIME (you can also
buy this at your local
hardware store) before
replacing the Nose Cone.
(see Fig. 18)
19. Ensure the Vent O Ring is
fitted correctly into the
groove and fully lubricated
with the supplied grease. (see
Fig. 18)
20. MAKE SURE to screw in the
Vent Plug to seal the vent.
21. Replace the Nose Cone and
close the Latches.
