Yamaha Raptor YFM35RA Скачать руководство пользователя страница 137

Страница: 137 / 142

Main switch  .................................................................... 4-1
Maintenance and lubrication chart  ................................. 8-5
Maintenance chart, emission control system  ................. 8-3
Maintenance record  ..................................................... 11-5
Model label ................................................................... 11-2

Neutral indicator light ..................................................... 4-2
Noise regulation ........................................................... 11-4

Owner’s manual and tool kit ........................................... 8-2

Parking ........................................................................... 6-7
Parking brake free play, adjusting ................................ 8-26
Parking brake lever  ........................................................ 4-6
Parking on a slope  ......................................................... 6-7
Part locations  ................................................................. 3-1

Reverse indicator light ................................................... 4-2
Riding your ATV ............................................................. 7-1

Start switch .................................................................... 4-3
Steering shaft, lubricating ............................................ 8-37
Storage .......................................................................... 9-2
Suspension, lubricating the upper and lower arm

pivots ......................................................................... 8-36

Suspension relay arm and connecting arm pivoting

points, lubricating the rear ......................................... 8-35

Swingarm pivots, lubricating ........................................ 8-34

Tail/brake light bulb, replacing  ..................................... 8-43
Throttle cable free play, adjusting  ................................ 8-21
Throttle lever  ........................................................... 4-3, 5-3
Tires ............................................................................... 5-4
Troubleshooting ........................................................... 8-44
Troubleshooting chart  .................................................. 8-46

Valve clearance  ........................................................... 8-22
Vehicle Emission Control Information label  ................. 11-2
Vehicle identification number  ....................................... 11-1

Warranty, extended  ..................................................... 11-8
Warranty, limited  .......................................................... 11-6
Wheel hub bearings, checking ..................................... 8-34
Wheel, installing ........................................................... 8-44
Wheel, removing  .......................................................... 8-44

U1BS11E0.book Page 2 Monday, April 5, 2010 8:56 AM

Содержание Raptor YFM35RA















































































































































Результаты поиска

Содержание Raptor YFM35RA

Отзывы:

Yamaha Raptor YFM35RA, Руководство пользователя, Страница: 137 / 142

Результаты поиска

Содержание Raptor YFM35RA

Отзывы: